What tools are required to replace the drive pinion bearings on 8.6, 9.5, and 11.5 inch axles on GMC Yukon?

To replace the drive pinion bearings on 8.6, 9.5, and 11.5 inch axles, the following tools are required: j 7818 (Inner Bearing Race Installer), j 8092 (Universal Driver Handle - 3/4 in - 10), j 8611-01 (Rear Pinion Bearing Race Installer), j 8614-01 (Flange and Pulley Holding Tool), j 22306 (Pinion Cup Bearing Installer - Rear), j 22912-b (Split Plate Bearing Puller), j 22828 (Input/Counterbalance Race Installer), dt-47688 (Pinion Bearing Remover, 8.6 Inch Axle Installer), j 36614 (Inner Pinion Bearing Installer), and j 45870 (Pinion Bearing Cup Installer). Raising the vehicle first allows access to Differential assembly removal. The dt-47688 tool should be used to extract the drive Pinion Bearing while separating it from the axle before removing this component. You should remove the shim followed by the outer and inner Pinion Bearing cups from the axle housing by using a hammer together with a brass drift. The installation requires j 8611-01 or j 7818 for the outer Pinion Bearing cup together with j 45870 or j 22306 and j 8092. Cut the drive pinion selective shim according to measurements then place it between the inner Pinion Bearing and gear shoulder. Place the inner Pinion Bearing by using j 24433 or j 36614 before adding a new collapsible spacer. Perform lubrication of the pinion bearings next. Put the outer Pinion Bearing inside the axle housing followed by insertion of new pinion oil seal through use of j 22388 tool. The service technician should install the pinion into its housing along with pinion sealant application to the yoke splines before installing the yoke while matching alignment marks used for removal. Place the pinion yoke onto the pinion shaft before installing both the washer along with a new pinion nut. The technician should use the j 8614-01 clamp to stabilize the pinion yoke during nut tightening procedures until the proper pinion end play is achieved while maintaining continuous pinion rotation. The measuring tool for pinion rotating torque should reach 1.0-2.3 n.m (10-20 lb in) for used bearings or 1.7-3.4 n.m (15-30 lb in) for new bearings. Adjustments can be made according to these settings. Repeated pinion rotations following the torque specification help seat the bearings before another torque measurement check is performed. The Differential assembly should be reinstalled and the axle should be filled with its proper lubricant then the vehicle needs to be lowered.

OEM GMC Yukon Pinion Bearing

Transmission Pinion Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Pinion Bearings found

View related parts
GMC Yukon Pinion Bearings
Part Number: 454021
$161.60 MSRP: $292.48
You Save: $130.88 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear; Differential Pinion Bearing; Rear Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion; Rear Wheel Bearing.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006, 1992-2000 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Pinion Seal, Outer
Part Number: 25824252
$50.72 MSRP: $95.24
You Save: $44.52 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Pinion Bearings; Side Bearings; Bearing; Bearing, Pinion Shaft Front
- Position: Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX
View related parts
GMC Yukon Side Bearings
Part Number: 88943839
$48.83 MSRP: $144.56
You Save: $95.73 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Bearing
- Replaces: 26091723
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Pinion Bearings
Part Number: 23243839
$71.22 MSRP: $139.44
You Save: $68.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Rear Pinion Bearing; Front/Inner/Outer Pinion; Diff/Drive Axle; Pinion/Clutch/Rear Wheel
- Position: Front
- Replaces: 09418357, 26053758, 9418357, 15286375, 20997052, 22786621, 9418356, 09418356, 12479221
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2020 GMC Yukon | Base, Denali, GT, Hybrid, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Pinion Bearings, Inner
Part Number: 457108
$55.00 MSRP: $154.36
You Save: $99.36 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion Bearings.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2013 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Pinion Bearings, Rear
Part Number: 22943106
$70.17 MSRP: $136.18
You Save: $66.01 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Drive Pinion Rear And Intermediate; Differential Pinion Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Side Bearings
Part Number: 11505123
$56.18 MSRP: $166.26
You Save: $110.08 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing; Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2013 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Pinion Bearings
Part Number: 9413427
$56.84 MSRP: $109.76
You Save: $52.92 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearings; Differential Drive, Steering Knuckle King, Pinion Shaft, Front Axle Bearings.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2020 GMC Yukon | Denali, Denali Hybrid, Hybrid, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Side Bearings
Part Number: 84881469
$55.61 MSRP: $99.30
You Save: $43.69 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Pinion Bearings, Outer
Part Number: 15534483
$53.12 MSRP: $94.85
You Save: $41.73 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Front Pinion Bearing; Bearing, Differential Pinion; Bearing, Pinion Shaft Front
- Position: Outer
- Replaces: 09440836, 9440836
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Pinion Bearings, Rear
Part Number: 84881466
$67.00 MSRP: $119.64
You Save: $52.64 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Drive Pinion Rear And Intermediate; Differential Pinion Bearing; Differential Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Pinion Bearings
Part Number: 84428299
$23.92 MSRP: $44.91
You Save: $20.99 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Front Pinion Bearing
- Position: Front
- Replaced by: 85722137
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Output Shaft Bearing
Part Number: 84766413
$23.15 MSRP: $41.33
You Save: $18.18 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing; Axle Bearing; Side Bearings
- Replaces: 84446291
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Pinion Bearings, Outer
Part Number: 22943109
$46.36 MSRP: $87.05
You Save: $40.69 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Axle Bearing; Outer Bearing; Bearing, Pinion Shaft Front
- Position: Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Pinion Bearings, Front Outer
Part Number: 84428300
$13.64 MSRP: $25.62
You Save: $11.98 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Front Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear Pinion Bearing; Bearing, Differential Pinion
- Position: Front Outer
- Replaced by: 85722136
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Pinion Bearings
Part Number: 9414917
$70.11 MSRP: $133.08
You Save: $62.97 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Differential Bearing; Rear Pinion Bearing; Drive Pinion Rear; Axle Pinion Shaft; Ring And Pinion; Pinion Shaft Front.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Pinion Bearings, Rear
Part Number: 22943107
$56.16 MSRP: $154.40
You Save: $98.24 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Drive Pinion Rear And Intermediate; Differential Pinion Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2023 GMC Yukon | AT4, Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Pinion Bearings
Part Number: 9413168
$93.86 MSRP: $167.61
You Save: $73.75 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Roller; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Drive Pinion Bearing Assembly.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Pinion Bearings
Part Number: 9417781
$43.00 MSRP: $103.28
You Save: $60.28 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearing; Differential Drive Pinion Front, Drive Pinion, Pinion Shaft Front, Front Axle
- Position: Front Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2013 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Side Bearings
Part Number: 22786619
$124.23 MSRP: $241.12
You Save: $116.89 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

GMC Yukon Pinion Bearing

Our website offers an extensive catalog of genuine GMC Yukon Pinion Bearing at unbeatable prices. Every OEM GMC Yukon Pinion Bearing comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

GMC Yukon Pinion Bearing Parts Questions & Experts Answers

Pinion Bearings
9413427
Q: What tools are required to replace the drive pinion bearings on 8.6, 9.5, and 11.5 inch axles on GMC Yukon?
A: To replace the drive pinion bearings on 8.6, 9.5, and 11.5 inch axles, the following tools are required: j 7818 (Inner Bearing Race Installer), j 8092 (Universal Driver Handle - 3/4 in - 10), j 8611-01 (Rear Pinion Bearing Race Installer), j 8614-01 (Flange and Pulley Holding Tool), j 22306 (Pinion Cup Bearing Installer - Rear), j 22912-b (Split Plate Bearing Puller), j 22828 (Input/Counterbalance Race Installer), dt-47688 (Pinion Bearing Remover, 8.6 Inch Axle Installer), j 36614 (Inner Pinion Bearing Installer), and j 45870 (Pinion Bearing Cup Installer). Raising the vehicle first allows access to Differential assembly removal. The dt-47688 tool should be used to extract the drive Pinion Bearing while separating it from the axle before removing this component. You should remove the shim followed by the outer and inner Pinion Bearing cups from the axle housing by using a hammer together with a brass drift. The installation requires j 8611-01 or j 7818 for the outer Pinion Bearing cup together with j 45870 or j 22306 and j 8092. Cut the drive pinion selective shim according to measurements then place it between the inner Pinion Bearing and gear shoulder. Place the inner Pinion Bearing by using j 24433 or j 36614 before adding a new collapsible spacer. Perform lubrication of the pinion bearings next. Put the outer Pinion Bearing inside the axle housing followed by insertion of new pinion oil seal through use of j 22388 tool. The service technician should install the pinion into its housing along with pinion sealant application to the yoke splines before installing the yoke while matching alignment marks used for removal. Place the pinion yoke onto the pinion shaft before installing both the washer along with a new pinion nut. The technician should use the j 8614-01 clamp to stabilize the pinion yoke during nut tightening procedures until the proper pinion end play is achieved while maintaining continuous pinion rotation. The measuring tool for pinion rotating torque should reach 1.0-2.3 n.m (10-20 lb in) for used bearings or 1.7-3.4 n.m (15-30 lb in) for new bearings. Adjustments can be made according to these settings. Repeated pinion rotations following the torque specification help seat the bearings before another torque measurement check is performed. The Differential assembly should be reinstalled and the axle should be filled with its proper lubricant then the vehicle needs to be lowered.