Make sure this part fits

GM 26073372
Boot Kit, Front

2000-2011 GM

Customer Questions & Expert Answers (14)
GM 26073372 Boot Kit, Front
  • Part Description
    Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
  • Position
    Front
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2008 Buick LaCrosseCXS6 Cyl 3.6 L GAS
    2000-2005 Buick LeSabreCustom, Limited6 Cyl 3.8 L GAS
    2009-2011 Buick LucerneCX, CXL, CXL Special Edition6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2000-2005 Buick Park AvenueBase, Ultra6 Cyl 3.8 L GAS
    2000-2004 Buick RegalGS, GSE, LS, LSE6 Cyl 3.8 L GAS
    2000-2011 Chevrolet Impala50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2000-2005 Chevrolet Monte CarloLS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    2001-2002 Oldsmobile AuroraBase6 Cyl 3.5 L GAS
    2000-2002 Oldsmobile IntrigueGL, GLS, GX6 Cyl 3.5 L GAS
    2000-2005 Pontiac BonnevilleSE, SLE6 Cyl 3.8 L GAS
    View More
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 26073372 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 26073372 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after crimping the eared clamp for the 2008 Buick LaCrosse? Posted by Customer
    A:
    If equipped, install the spacer ring into the groove of the halfshaft bar using J 8059, then slide the tripot joint spider assembly as far as it will go on the halfshaft bar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you pack the CV joint with grease for the 2010 Buick Lucerne? Posted by Customer
    A:
    Insert the chrome balls, packing the CV joint with grease from the service kit, and push the CV joint onto the halfshaft bar until the retaining ring is seated.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the procedure for tightening the bolts for the 2000 Buick Park Avenue? Posted by Customer
    A:
    Insert and tighten the bolts until snug, ensuring no pinch points on the halfshaft inboard boot.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be done with the CV joint cage and chrome alloy balls for the 2000 Buick LeSabre? Posted by Customer
    A:
    Remove the boot from the bar and gently tap on the CV joint cage with a brass drift and hammer to remove the chrome alloy balls.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be done with the grease on the CV joint inner race for the 2000 Buick Park Avenue? Posted by Customer
    A:
    Wipe the grease from the CV joint inner race and spread the ears on the race retaining ring with the Snap Ring Pliers (J 8059) to remove the CV joint assembly from the bar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you remove the spider assembly for the 2000 Buick LeSabre? Posted by Customer
    A:
    Use Snap Ring Pliers (J 8059) to spread the spacer rings and remove the spider assembly, followed by the spacer ring, spider assembly, second spacer ring, and inboard boot.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the final step in the installation process for the 2008 Buick LaCrosse? Posted by Customer
    A:
    Slide the outboard seal with the large seal retaining clamp over the CV joint outer race and crimp the clamp using the J 35910 to 174 N.m (130 lb ft), ensuring the gap dimension is reached.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you insert the chrome balls for the 2009 Buick Lucerne? Posted by Customer
    A:
    Insert the chrome balls, alternating directions until all are in place, then pack the CV joint with grease, placing half inside the outboard seal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the next step after sliding the boot onto the halfshaft bar for the 2000 Buick Regal? Posted by Customer
    A:
    Position it in the boot groove.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the next step after packing the CV joint with grease for the 2010 Chevrolet Impala? Posted by Customer
    A:
    Install the CV joint onto the wheel drive shaft using a block of wood and a hammer.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you separate the outboard boot from the CV joint for the 2000 Chevrolet Monte Carlo? Posted by Customer
    A:
    Slide the outboard boot away from the CV joint along the bar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you remove the outer retaining ring from the wheel drive shaft for the 2009 Chevrolet Impala? Posted by Customer
    A:
    Use the appropriate tool to remove the outer retaining ring.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be inspected and cleaned before starting the replacement for the 2000 Chevrolet Monte Carlo? Posted by Customer
    A:
    Inspect the transmission sealing surface of the halfshaft for corrosion and clean it with 320 grit cloth if necessary.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Boot Kit, Front 26073372 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 26073372 Boot Kit, Front is available in the market under the name GM CV Boot. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 26073372 Boot Kit, Front fits certain Chevrolet Impala, Monte Carlo models, as well as Buick Regal, LaCrosse, LeSabre. Additionally, it is compatible with Pontiac Grand Prix, Bonneville and Oldsmobile Aurora, Intrigue models.
The original GM component designated by manufacturer part number 26073372 maintains top performance when functioning as the Boot Kit, Front Wheel Drive Axle Shaft; CV Boot unit at its Front. The component 26073372 is constructed from durable material and its dimensions span 7.7 x 6.9 x 7.0 inches while weighing 0.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Inner Boot; Inner Boot Kit; Boots. The part 26073372 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.