Make sure this part fits

GM 88964425
Overhaul Kit

2002-2005 GM

Customer Questions & Expert Answers (14)
GM 88964425 Overhaul Kit
  • Part Description
    Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit
  • Position
    Front
  • Replaces
    12497787
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2005 Buick RainierCXL, CXL Plus6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2003-2005 Chevrolet SSRBase8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2002-2005 Chevrolet TrailblazerLS, LT, LTZ, North Face6 Cyl 4.2 L GAS
    2002-2005 Chevrolet Trailblazer EXTLS, LT, North Face6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2002-2005 GMC EnvoyDenali, SLE, SLT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2002-2005 GMC Envoy XLDenali, SLE, SLT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2004-2005 GMC Envoy XUVSLE, SLT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2002-2004 Oldsmobile BravadaBase6 Cyl 4.2 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is 88964425 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88964425 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after installing the front brake caliper for the 2005 Buick Rainier? Posted by Customer
    A:
    Install the front brake caliper guide pin bolts and tighten them to 42 Nm (31 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if reusing the brake caliper guide pin for the 2004 Buick Rainier? Posted by Customer
    A:
    Clean it with denatured alcohol or an equivalent, dry it using non-lubricated, filtered air, and apply high temperature silicone brake lubricant, avoiding contact with the brake pad hardware.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after removing the tire and wheel assembly for the 2003 Chevrolet SSR? Posted by Customer
    A:
    Detach the rear brake hose bolt from the rear brake caliper and plug the opening of the brake hose to prevent excessive brake fluid loss and contamination.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you remove the rear brake caliper for the 2004 Chevrolet SSR? Posted by Customer
    A:
    Take out the rear brake caliper mounting bolts and remove the rear brake caliper from the mounting bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if reusing the brake caliper guide pin for the 2005 Chevrolet SSR? Posted by Customer
    A:
    Clean it with denatured alcohol and dry it using non-lubricated, filtered air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after removing the tire and wheel assembly for the 2005 Chevrolet Trailblazer? Posted by Customer
    A:
    Detach the rear brake hose bolt from the rear brake caliper and plug the opening of the brake hose to prevent excessive brake fluid loss and contamination.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step in the process for the 2004 Chevrolet Trailblazer? Posted by Customer
    A:
    Bleed the hydraulic brake system, reinstall the tire and wheel assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What components should be taken out next for the 2003 Chevrolet Trailblazer? Posted by Customer
    A:
    Take out the bleeder valve and cap, as well as the guide pins and sleeves from the anchor bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step to replace the rear brake caliper for the 2002 Chevrolet Trailblazer? Posted by Customer
    A:
    Raise the vehicle and remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the torque specification for tightening the bleeder valve for the 2005 GMC Envoy? Posted by Customer
    A:
    Tighten the bleeder valve to 12 Nm (110 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What safety precaution should be taken while applying compressed air for the 2002 GMC Envoy? Posted by Customer
    A:
    Exercise caution to avoid placing fingers in front of the piston while applying compressed air, as this may cause serious injury.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the guide pins and brake pad retaining clips be prepared for reuse for the 2003 GMC Envoy? Posted by Customer
    A:
    Clean them with denatured alcohol and dry them with non-lubricated, filtered air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if reusing the brake caliper guide pin for the 2002 Chevrolet Trailblazer? Posted by Customer
    A:
    Clean it with denatured alcohol and dry it using non-lubricated, filtered air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Overhaul Kit 88964425 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88964425 Overhaul Kit is available in the market under the name GM Brake Caliper Repair Kit, Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88964425 Overhaul Kit fits certain Chevrolet SSR, Trailblazer, Trailblazer EXT models, as well as GMC Envoy, Envoy XL, Envoy XUV. Additionally, it is compatible with Buick Rainier and Oldsmobile Bravada models.
The original GM component designated by manufacturer part number 88964425 maintains top performance when functioning as the Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit unit at its Front. The component 88964425 is constructed from durable material and its dimensions span 5.2 x 3.1 x 14.7 inches while weighing 1.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Caliper Kit, Wheel Brake Cylinder/Caliper. The part 88964425 has available replacement options 12497787. Each vehicle needs 2 units of the part marked as SKU 88964425. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.