GM 84509133
Door Check, Passenger Side

You need to start by opening the door halfway then drawing the side door check toward the door interior before continuing with opening the door. First detach the fasteners which connect the side door check to the door pillar before extracting the check from the door. The installation of new side door check requires positioning the check inside the door and fastening it to the pin while drawing the check to activate the pin. Seal the side door check to its position on the door pillar with fasteners which should be tightened to 10 Nm (89 lb in). Vehicle owners must maintain strict caution in fastening procedures to stop equipment-related damages to their vehicles.

Begin installation by opening the doorway halfway and pulling the side door check towards the door interior before completing the door opening. Take off all fasteners securing the side door check to the door pillar before extracting the check from the door frame. To install the side door check place it inside the door while connecting it to the pin located within the door before pulling the check to activate the pin. Finish by mounting the fasteners to the door pillar and tighten them to 10 Nm (89 lb in).

Replace the rear side door upper check by starting with the sliding side door opening followed by carefully removing the sliding side Door Check from the door. When installing this component you should first apply mild soap to the sliding side check before putting it on the sliding door.

The first step to replace the front door check begins with removing the front door trim panel together with the front door water deflector. Guidelines now follow to uninstall the door jamb bolts which connect the check to the door trim together with the door check securing nuts before beginning. The new door check installation requires following the fastener notice while connecting it to the door because the proper seat must be achieved. Fit the door check into its place then fasten the two nuts to 11 N.m (97 lb in) torque before re-installation of the bolts to establish the door check to the door jamb by using 11 N.m (97 lb in). The installation process concludes with the replacement of front door water deflector followed by installation of front door trim panel.

The procedure to replace the front side door check begins by removing front door trim panel together with the front door water deflector. Search and withdraw the door check securing bolts that attach to the door jamb and the door then remove the check from the door. Screw the door check to the door after ensuring proper placement of its nuts followed by tightening them to 11 Nm (97 lb in). Install the door check bolts on the door jamb after which tighten them to 11 Nm (97 lb in). The operation ends by reattaching both the front door water deflector and the front door trim panel.

The process of installing a new rear side door check starts with pulling the strap toward the door interior when you halfway open the door. Complete the replacement by opening the door. First remove the fasteners holding the side door check to the door pillar before taking the strap out from the door. You should insert the side door check once more through the door opening then attach it to the door's internal pin before pulling the strap into position. Fasteners should be installed to fix the side door check to the door pillar while tightening bolt or nut values to 10 N.m (89 lb in).

The process starts with unhinging the front door trim panel and front door water deflector before moving to replace the front side door check. Start by removing the bolts from the door check where it joins the door jamb then proceed to separate the two nuts attaching the check to the door before taking out the door check. The first step for installation calls for connecting the door check to the door while keeping in mind the Fastener Notice instructions. First, clamp the door check with two nuts and tighten them to 11 N.m (97 lb in) before placing back the bolts to fasten the door check to the door jamb and torque them to 11 N.m (97 lb in). The final installation step includes putting back the front door water deflector together with the front door trim panel.

Install the fasteners to secure the side door check strap to the door pillar, tightening the bolts or nuts to 10 N.m (89 lb in).

Open the door approximately halfway and pull the side door check strap toward the inside of the door before swinging the door open.

Begin by removing the front door trim panel and the front door water deflector.

Install the two nuts to secure the check assembly to the track, tightening them to 10 Nm (89 lb in).

Remove the fasteners that secure the side door check strap to the door pillar and take out the side door check strap from the door.

Reinstall the passenger side body side trim panel.

Install the bolts to secure the door link to the door jamb, also tightening them to 11 Nm (97 lb in).

Install the fasteners to secure the side door check strap to the door pillar, tightening the bolts or nuts to 10 N.m (89 lb in).

Tighten them to 10 Nm (89 lb in).

Open the door approximately halfway and pull the side door check strap toward the inside of the door before swinging the door open.

Install the fasteners to secure the side door check strap to the door pillar and tighten them to 10 Nm (89 lb in).

Place the side door check strap back into the door and hook it to the pin inside the door, ensuring to pull the strap to engage the pin.

Place the side door check strap back into the door and hook it to the pin inside, ensuring to pull the strap to engage the pin.

The two nuts that hold the door link to the door.