GM 15783575
Lock Cylinder, Front

The process of replacing the Door Lock Cylinder requires beginning with fully raising the window. The first step involves removing both the front door trim panel together with the water deflector. Start by removing both the front door trim panel and water deflector. After that take off the outside Door Handle before unclipping the lock cylinder lever from the cylinder. Once the lock cylinder retainer is gone from the installation. The lock cylinder needs to be inserted into the outside Door Handle and then the clip can be installed. First reinstall the outside Door Handle followed by the front door water deflector and end with the front door trim panel.

The first step for Door Lock Cylinder replacement requires removing both the front door panel and front door water deflector. Start by detaching the front Door Lock Cylinder rod from the Door Lock before taking out the retainer and cylinder from the hole and rod. Place the lock cylinder rod onto the new front Door Lock Cylinder after which you should insert it through the lock cylinder hole. After attaching the retainer to the lock cylinder position replace the rod to the front Door Lock then reinstall the front door water deflector and the front door panel.

The first step for front Door Lock Cylinder replacement requires users to rise the window completely followed by removing the front door trim panel. Proceed to eliminate the water deflector along with the exterior Door Handle. Begin by taking off the clip from the lock cylinder lever to lock cylinder attachment before pressing the lock cylinder retainer out to remove the lock cylinder from the outside Door Handle. First install the lock cylinder inside the outside Door Handle until it locks the cylinder retainer before adding the lever clip to keep the lock cylinder lever connected to the cylinder . After reinstalling the outside Door Handle you should install the front door water deflector and conclude with the front door trim panel.

The outside Door Handle removal serves as the first step before Door Lock Cylinder replacement. A flat-bladed tool can be used to detach the Door Lock Cylinder retainer so you can remove the Door Lock Cylinder which is currently situated inside the outside Door Handle. The new lock cylinder installation requires a layer of suitable lubricant to be applied inside the lock case and cylinder keyway. It is crucial to mount the new Door Lock Cylinder onto the outside Door Handle after which you should position the Door Lock Cylinder retainer and return the outside Door Handle. The instructions for new lock cylinder coding can be found in key and lock cylinder coding in general information and the procedure for binding lock cylinder repair can be seen in binding lock cylinders.

The replacement process of rear door lock cylinders begins with removing the right side rear door trim panel. The next step requires removal of the outside Door Handle. Push the lock cylinder retainer while you remove the clip which fastens the lock cylinder lever to the lock cylinder . Proceed to pull out both the lock cylinder from the handle and from inside of the vehicle. Begin the installation step by placing the lock cylinder back into the vehicle then push it into the handle until the lock cylinder retainer locks in place. Insert the clip to maintain the connection between the lock cylinder lever and the lock cylinder before putting back the outside Door Handle. You must put back the right side rear door trim panel at the end of this installation.

The first step for Door Lock Cylinder replacement is to detach the front door panel and front door water deflector. Proceed by removing the front Door Lock Cylinder rod from its connection with the front Door Lock followed by eliminating the retainer of the lock cylinder from the cylinder hole together with the rod and lock cylinder. The new front Door Lock Cylinder starts with a lock cylinder rod installation before inserting it into the hole and fastening with the provided retainer. At first connect the lock rod to the front Door Lock before putting back both the water deflector and the front door panel.

The first requirement for Door Lock Cylinder replacement is to secure the new cylinder for substitution. Proper installation requires applying suitable lubricating material inside the lock case along with the cylinder keyway following recommended recommendations. Check the binding lock cylinders guidelines for the lock cylinder situation and use the key and lock cylinder coding information to code new lock cylinders. You must first remove the Door Handle outside then insert a flat-bladed tool to detach the Door Lock Cylinder retainer. Take the Door Lock Cylinder out from the outside Door Handle. To install the lock cylinder take it into the outside Door Handle then apply the Door Lock Cylinder retainer before you reinstall the outside Door Handle.

Install the lock cylinder back into the vehicle, pressing it into the handle to engage the lock cylinder retainer.

Insert the front door lock cylinder into the lock cylinder hole with the rod.

Finally, reinstall the rear door trim panel.

Disconnect the front door lock cylinder rod from the front door lock and remove the front door lock cylinder retainer.

Reinstall the outside door handle and then reinstall the right side rear door trim panel.

Press the lock cylinder retainer and then extract the lock cylinder from the handle and the vehicle.

Remove the outside door handle.

Press the lock cylinder into the handle.

Remove the right side rear door trim panel.

Use a flat-bladed tool to take out the door lock cylinder retainer and remove the door lock cylinder from the outside door handle.

Then, remove the clip that retains the lock cylinder lever to the lock cylinder.

Press the lock cylinder into the handle to engage the lock cylinder retainer.

Raise the window completely.

Remove the front door panel and the front door water deflector.