Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 25999685
Front Hub & Bearing

2006-2008 GM

Customer Questions & Expert Answers (7)
GM 25999685 Front Hub & Bearing
GM 25999685 Front Hub & Bearing
GM 25999685 Front Hub & Bearing
  • Part Description
    Hub Assembly-Front Wheel (W/ Bearing & Sensor); Wheel Bearing & Hub Repair Kit.
  • Position
    Front
  • Replaces
    88967258
  • Manufacturer
    General Motors
Make sure this part fits
$134.67 MSRP: $251.31
You Save: $116.64 (47%)
1
ADD TO CART

  • 25999685 Front Hub & Bearing is Ref No. 1 in the diagram below

    2007 Saturn Relay Front Hub & Bearing Diagram for 25999685
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 25999685

  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2007 Buick TerrazaCX, CXL6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006-2008 Chevrolet UplanderBase, LS, LT6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2006 Pontiac MontanaSV66 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2006-2007 Saturn Relay1, 2, 36 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25999685 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25999685 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front wheel bearing/hub on Buick Terraza? Posted by Customer
    A:
    First, lift and secure the vehicle before starting to change the front Wheel Bearing/hub. Take off the tire and wheel, and afterwards, pull off the wheel speed sensor electrical connector and loosen it from the bracket. After that, take off the Brake Caliper Bracket and brake caliper, and then remove the brake rotor. Loosen the wheel drive shaft nut, then screw on j 28733-b (Front Hub Spindle Remover) onto the Wheel Bearing/hub with three wheel nuts. With the j 28733-b, gently force the wheel drive shaft away from the Wheel Bearing/hub, and afterwards discard the Wheel Bearing/hub bolts, ensuring the wheel drive shaft outer seal boot does not get damaged. Replace the fasteners with new ones when attaching the new Wheel Bearing/hub to make sure the vehicle stays under control. Secure the new Wheel Bearing/hub bolts to 130 n.m (96 lb ft), put on the wheel drive be sure the connector clip is correctly attached to the bracket, and afterward connect the wheel speed sensor electrical connector to the bracket as well as reconnect the wheel speed sensor electrical connector . Put the wheel and tire on your vehicle after it is lowered.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front wheel bearing and hub on Chevrolet Uplander? Posted by Customer
    A:
    Start fixing front wheel bearings and hubs by raising the vehicle with proper support. Take off the tire and wheel before disconnecting and removing the Wheel Speed Sensor electrical connector from its bracket. Take off first the brake caliper housing together with its connected caliper and rotor unit. Place the removal tool j 28733-b on top of the Wheel Bearing hub and thread three wheel nuts onto it to prepare for pushing out the wheel drive shaft. With the j 28733-b tool push the wheel drive shaft out of the Wheel Bearing/hub while discarding and removing Wheel Bearing/hub bolts. Keep the outer seal boot intact during the process. Put in the new Wheel Bearing/hub and fasten it with new bolts before tightening it to 130 n.m (96 lb ft). Mount the wheel drive shaft nut, brake rotor, and Brake Caliper Bracket with brake caliper. Get the connector clip to enter its designated spot on the bracket. Last finish the setup by placing the Wheel Speed Sensor wiring on the bracket then link it up and put back the tire and wheel while lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    What needs to be disconnected next for the 2006 Buick Terraza? Posted by Customer
    A:
    Disconnect the wheel speed sensor electrical connector and detach it from the bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be done with the fasteners during installation for the 2007 Buick Terraza? Posted by Customer
    A:
    Replace the fasteners with new ones whenever they become loose or are removed.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What is the next step after discarding the bolts for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Remove the wheel bearing/hub.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What is the first step to replace the rear wheel bearing/hub assembly on an independent rear suspension for the 2006 Chevrolet Uplander? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Front Hub & Bearing 25999685 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25999685 Front Hub & Bearing is available in the market under the name GM Wheel Bearing, Wheel Hub. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25999685 Front Hub & Bearing fits certain Chevrolet Uplander models, as well as Buick Terraza. Additionally, it is compatible with Pontiac Montana and Saturn Relay models.
The original GM component designated by manufacturer part number 25999685 maintains top performance when functioning as the Hub Assembly-Front Wheel (W/ Bearing & Sensor); Wheel Bearing & Hub Repair Kit. unit at its Front. The component 25999685 is constructed from durable material and its dimensions span 9.5 x 8.9 x 6.9 inches while weighing 8.10 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hub & Bearing; Hub, Front Wheel Inner; Hub, Front Wheel; Hub, Rear Wheel. The part 25999685 has available replacement options 88967258. Each vehicle needs 2 units of the part marked as SKU 25999685. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.