Make sure this part fits

GM 25695932
Transmission Mount, Driver Side

1998-2005 GM

Customer Questions & Expert Answers (28)
GM 25695932 Transmission Mount, Driver Side
GM 25695932 Transmission Mount, Driver Side
  • Part Description
    Trans Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount
  • Position
    Driver Side
  • Replaces
    25662258, 25691733, 25689177, 25713700
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2000-2005 Buick LeSabreCustom, Limited6 Cyl 3.8 L GAS
    2000-2005 Buick Park AvenueBase, Ultra6 Cyl 3.8 L GAS
    2000-2005 Cadillac DeVilleBase, DHS, DTS, Protection Series8 Cyl 4.6 L GAS
    1998-2004 Cadillac SevilleSLS, STS8 Cyl 4.6 L GAS
    2001-2003, 1999 Oldsmobile AuroraBase6 Cyl 3.5 L GAS, 8 Cyl 4.0 L GAS
    2000-2005 Pontiac BonnevilleGXP, SE, SLE, SSEi6 Cyl 3.8 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25695932 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25695932 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after raising the 2003 Buick LeSabre? Posted by Customer
    A:
    Remove the nut that secures the front transmission mount to the frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after raising the 2005 Buick LeSabre? Posted by Customer
    A:
    Remove the nut that secures the front transmission mount to the frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    Where should a jack stand be placed for support for the 2001 Buick LeSabre? Posted by Customer
    A:
    Under the left side of the transmission.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be applied to the rear transmission bracket bolts for the 2004 Buick LeSabre? Posted by Customer
    A:
    Thread lock compound GM P/N 12345493 or equivalent.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after removing the lower bolts and nut for the 2002 Buick LeSabre? Posted by Customer
    A:
    Take out the three retaining bolts from the mount bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be removed after raising for the 2001 Buick Park Avenue? Posted by Customer
    A:
    The left front tire and wheel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the final step after securing the front transmission mount for the 2002 Buick LeSabre? Posted by Customer
    A:
    Lower the vehicle and reinstall the front transmission mount bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after installing the mount for the 2000 Buick Park Avenue? Posted by Customer
    A:
    Raise the powertrain with the jack stand to load the mount, then install the mount stud nut onto the mount stud and tighten it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be attached next after the retaining bolts for the 2003 Buick Park Avenue? Posted by Customer
    A:
    Attach the transmission mount lower bolts and nut onto the mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be installed after raising the engine and transmission assembly for the 2002 Cadillac Seville? Posted by Customer
    A:
    Install the nut to the mount and mount bracket, tightening it to 75 Nm (55 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What procedures should be followed when replacing mounts or brackets for the 2003 Buick Park Avenue? Posted by Customer
    A:
    Follow the procedures for Automatic Transmission Mount Replacement - Front, Left, Rear, and for Automatic Transmission Mount Bracket Replacement - Front, Left, and Rear.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done last before lowering the 2002 Buick Park Avenue? Posted by Customer
    A:
    Reinstall the power steering gear heat shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after removing the mount for the 2000 Buick LeSabre? Posted by Customer
    A:
    Slowly lower the powertrain using the jack stand and remove the mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be removed after the mount bracket nuts for the 2004 Buick Park Avenue? Posted by Customer
    A:
    Remove the lower bolts and nut from the mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after securing the mount to the frame for the 2002 Cadillac DeVille? Posted by Customer
    A:
    Lower the transmission into position and install the nuts to the mount and mount bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should you do to prevent damage to the oil pan for the 2004 Cadillac DeVille? Posted by Customer
    A:
    Place a block of wood spanning the width of the oil pan bottom between it and the jack support.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after securing the mount to the frame for the 2000 Cadillac DeVille? Posted by Customer
    A:
    Lower the transmission into position and install the nut to the mount and mount bracket, tightening it to 75 Nm (55 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to replace the left automatic transmission mount for the 2004 Cadillac DeVille? Posted by Customer
    A:
    Raise and support the vehicle, then support the powertrain assembly with a suitable jack.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after installing the mount for the 2001 Cadillac DeVille? Posted by Customer
    A:
    Attach the mount bolt and nut to the frame, ensuring to tighten the nuts to 70 Nm (52 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be removed after supporting the 2001 Cadillac Seville? Posted by Customer
    A:
    Remove the nut securing the transmission mount to the transmission mount bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next action after removing the nuts for the 2000 Cadillac Seville? Posted by Customer
    A:
    Raise the jack slightly to lift the engine assembly from the subframe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What procedures should be followed when replacing the mounts or brackets for the 2003 Cadillac Seville? Posted by Customer
    A:
    Follow the procedures for Automatic Transmission Mount Replacement - Left, Automatic Transmission Mount Replacement - Rear, Automatic Transmission Mount Bracket Replacement - Left, and Transmission Mount Bracket Replacement - Rear.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should you do after raising the 2004 Cadillac Seville? Posted by Customer
    A:
    Next, raise the transmission/transaxle to create slight tension in the mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after removing the nuts for the 2002 Cadillac Seville? Posted by Customer
    A:
    Raise the jack slightly to lift the engine assembly from the engine frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step in the installation process for the 2005 Buick LeSabre? Posted by Customer
    A:
    Position the mount and the mount bracket onto the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should you do after raising the 2003 Cadillac DeVille? Posted by Customer
    A:
    Elevate the transmission/transaxle to create slight tension in the mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be used to support the transaxle for the 2005 Buick Park Avenue? Posted by Customer
    A:
    Use a transaxle support stand.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Transmission Mount, Driver Side 25695932 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25695932 Transmission Mount, Driver Side is available in the market under the name GM Motor And Transmission Mount. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25695932 Transmission Mount, Driver Side fits certain Cadillac DeVille, Seville models, as well as Buick LeSabre, Park Avenue. Additionally, it is compatible with Pontiac Bonneville and Oldsmobile Aurora models.
The original GM component designated by manufacturer part number 25695932 maintains top performance when functioning as the Trans Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount unit at its Driver Side. The component 25695932 is constructed from durable material and its dimensions span 8.1 x 6.8 x 4.7 inches while weighing 4.00 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Side Transmission Mount; Mount; Mount, Transmission Mounting. The part 25695932 has available replacement options 25662258, 25691733, 25689177, 25713700. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.