Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 25778605
Brake Booster

2004-2008 GM

Customer Questions & Expert Answers (7)
GM 25778605 Brake Booster
  • Part Description
    Booster, Hydraulic Power Brake Booster
  • Replaces
    10382217, 15285078, 22735692
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • 2008 Chevy Malibu Brake Booster Diagram for 25778605
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 25778605

  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2008 Chevrolet MalibuBase, Classic LS, Classic LT, LS, LT, LTZ, Maxx, Maxx LS, Maxx LT, Maxx LTZ, Maxx SS, SS4 Cyl 2.2 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2005-2007 Pontiac G6Base, GT, GTP4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25778605 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25778605 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Vacuum Brake Booster (ABS) on Chevrolet Malibu? Posted by Customer
    A:
    Begin the vacuum Brake Booster replacement task by securing power off the vehicle to defend from ebcm/ebtcm malfunction. Supported under the vehicle position your left front wheel assembly to access its installation point. Use a socket to remove 3 wireless ebcm/bpmv bracket nuts on the left front wheelhouse and lower the entire automobile. Pull the ebcm electrical connector back while discharging Brake Booster vacuum through the vacuum check valve on its grommet retaining spot without breaking the vacuum hose connection. Insert bleeder valve caps into each of the 4 brake pipes at the bpmv to stop fluid loss while maintenance. Remove the vacuum Brake Booster master cylinder nuts then detach the ebcm/bpmv bracket assembly together with the brake master cylinder. Take out the two Brake Pedal assembly to cowl nuts and remover the brake apply sensor and closeout panel from the electrical connector. To free the pushrod from the Brake Pedal pin remove the connection parts including the pushrod retaining clip , wave washers and booster pushrod while tilting the booster to separate the parts without forceful side pressure. Take out the booster unit from the vehicle. Return the booster to its position and tilt the unit to match the pushrod with the Brake Pedal pin while installing without pressing too hard. Thread the Brake Booster pushrod retaining clip, wave washers, and Brake Pedal pushrod connections back to the Brake Pedal pin. Install the 2 Brake Pedal assembly to cowl mounting nuts but tighten them to 15 nm (11 ft. Lbs.). Put back the electrical brake apply sensor connector before mounting the master cylinder gasket side with the jp1 and ebcm/bpmv bracket. Fasten the master cylinder screws to the vacuum Brake Booster securing unit with 25 nm (18 foot lbs.) torque. Continuing with the vehicle raised put on the 3 bracket assembly ebcm/bpmv nuts to the left wheelhouse, snug down to 10 nm (86 inch lbs.) before reattaching the wheel and tire apparatus left front. Seal-free brake pipe ends and match up the 4 connections to the bpmv unit. Tighten each connection to 20 nm (15 ft. Lbs). Plug in the electrical connector to its place on the ebcm and attach the vacuum Brake Booster check valve to the new grommet at the vacuum Brake Booster. Close the hydraulic brake system and adjust the Brake Pedal position sensor after doing this step.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after reconnecting the brake pedal components for the 2004 Chevrolet Malibu? Posted by Customer
    A:
    Reattach the electrical connector to the brake apply sensor and install the closeout panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Booster
    Q:
    What needs to be detached from the left front wheelhouse for the 2007 Chevrolet Malibu? Posted by Customer
    A:
    Remove the 2 nuts that attach the proportioning valve bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Booster
    Q:
    What should be done after depleting the vacuum reserve for the 2008 Chevrolet Malibu? Posted by Customer
    A:
    Raise and support the vehicle, then remove the left front tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Booster
    Q:
    What components need to be disconnected next for the 2006 Chevrolet Malibu? Posted by Customer
    A:
    Remove the closeout panel and the electrical connector from the brake apply sensor, followed by the 2 brake pedal assembly to cowl mounting nuts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Booster
    Q:
    What is the first step to replace the Vacuum Brake Booster (ABS) for the 2005 Chevrolet Malibu? Posted by Customer
    A:
    Turn the ignition to the OFF position to prevent damage to the EBCM/EBTCM when disconnecting the wiring harness.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Booster
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Brake Booster 25778605 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25778605 Brake Booster is available in the market under the name GM Brake Booster. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25778605 Brake Booster fits certain Chevrolet Malibu models, as well as Pontiac G6 models.
The original GM component designated by manufacturer part number 25778605 maintains top performance when functioning as the Booster, Hydraulic Power Brake Booster unit. The component 25778605 is constructed from durable material and its dimensions span 12.0 x 16.3 x 11.8 inches while weighing 7.70 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Booster. The part 25778605 has available replacement options 10382217, 15285078, 22735692. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.