Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 15763216
Steering Wheel

1999-2005 GM

Customer Questions & Expert Answers (8)
GM 15763216 Steering Wheel
GM 15763216 Steering Wheel
GM 15763216 Steering Wheel
  • Part Description
    Wheel, Steering
  • Replaces
    16822251
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 15763216 Steering Wheel is Ref No. 15 in the diagram below

    2001 GMC Sierra 1500 Steering Wheel Diagram for 15763216
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 15763216

  • Vehicle Fitment

    Year Make Model Trim Engine
    2005 Chevrolet AstroBase, LS, LT6 Cyl 4.3 L GAS
    2002 Chevrolet Avalanche 1500Base, North Face, On Road Edition, Z718 Cyl 5.3 L GAS
    2002 Chevrolet Avalanche 2500Base8 Cyl 8.1 L GAS
    1999-2005 Chevrolet BlazerBase, LS, LT, Trailblazer, Xtreme, ZR26 Cyl 4.3 L GAS
    2001-2002 Chevrolet Express 1500Base, LS, LT6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
    2001-2002 Chevrolet Express 2500Base, LS6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
    2001-2002 Chevrolet Express 3500Base, LS8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 8.1 L GAS
    1999-2004 Chevrolet S10Base, LS, Xtreme, ZR2, ZR54 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
    1999-2002 Chevrolet Silverado 1500Base, LS, LT, WT6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2001-2002 Chevrolet Silverado 1500 HDLS, LT8 Cyl 6.0 L GAS
    View More
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 15763216 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15763216 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Service and Repair a Steering Wheel on Chevrolet Blazer? Posted by Customer
    A:
    Start by disabling the restraints system then remove the inflator module before attempting a Steering Wheel replacement. Press the horn plunger into the Steering Column stop before rotating it 90 degrees to remove it. Vehicles utilizing dual Steering Wheel controls should disengage their electrical Steering Wheel connector. Start by removing the Steering Wheel retaining nut from the Steering Shaft then document correct wheel shaft alignment points which you will need during Steering Wheel reinstallation. J 1859-a (J 1859-A) must be used as a Steering Wheel puller because it protects the Steering Column from damage. The Steering Wheel requires j 1859-a (J 1859-A) installation before removing the wheel. When installing the Steering Wheel position the multifunction switch turn signal into the neutral position then carefully match the Steering Wheel mark to the Steering Shaft before installing it. Fits the Steering Wheel retaining nut onto the Steering Shaft then torque it to 41 nm (30 ft. Lbs.). Vehicles requiring redundant controls require Steering Wheel electrical connector reconnection before horn plunger and inflator module installation to enable the restraints system.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the steering wheel on Chevrolet Blazer? Posted by Customer
    A:
    Steering Wheel replacement starts with disabling the sir system followed by inflator module removal. Press and hold the Steering Column's horn plunger towards its stop mark then rotate it 90 degrees clockwise. Disconnection of Steering Wheel electrical connections remains necessary for vehicles equipped with repeated Steering Wheel control systems. Before you reinstall the Steering Wheel keep the nut that holds the Steering Wheel to the Steering Shaft then make marks to align the Steering Wheel and Steering Shaft correctly. The j 1859-a (J 1859-A) Steering Wheel puller requires usage because striking the Steering Column shaft's end with a hammer might cause the plastic injections that hold the column steady to loosen. Detach the Steering Wheel while using j 1859-a (J 1859-A) on the wheel previously installed. Remove j 1859-a (J 1859-A) from the Steering Wheel. For new Steering Wheel installation start by setting your multifunction switch turn signal to neutral before matching the Steering Wheel's mark to the Steering Shaft. Then secure the Steering Wheel on the shaft. Fitting the Steering Wheel retaining nut requires torque to 41 nm or 30 ft. Lbs. A vehicle with redundant Steering Wheel controls needs its electrical connector reconnected first before users install the horn plunger and inflator module to enable the sir system.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the steering wheel on Chevrolet S10? Posted by Customer
    A:
    Steering Wheel replacement starts with disabling the sir system followed by inflator module removal. Press and hold the Steering Column's horn plunger towards its stop mark then rotate it 90 degrees clockwise. Disconnection of Steering Wheel electrical connections remains necessary for vehicles equipped with repeated Steering Wheel control systems. Before you reinstall the Steering Wheel keep the nut that holds the Steering Wheel to the Steering Shaft then make marks to align the Steering Wheel and Steering Shaft correctly. The j 1859-a (J 1859-A) Steering Wheel puller requires usage because striking the Steering Column shaft's end with a hammer might cause the plastic injections that hold the column steady to loosen. Detach the Steering Wheel while using j 1859-a (J 1859-A) on the wheel previously installed. Remove j 1859-a (J 1859-A) from the Steering Wheel. For new Steering Wheel installation start by setting your multifunction switch turn signal to neutral before matching the Steering Wheel's mark to the Steering Shaft. Then secure the Steering Wheel on the shaft. Fitting the Steering Wheel retaining nut requires torque to 41 nm or 30 ft. Lbs. A vehicle with redundant Steering Wheel controls needs its electrical connector reconnected first before users install the horn plunger and inflator module to enable the sir system.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the steering wheel on GMC Safari? Posted by Customer
    A:
    Before removing the Steering Wheel, first turn the restraints system off. Pull out the Steering Wheel inflator module and the horn plunger from the Steering Column by pressing in to stop and turning it 90 degrees. Then, take off the Steering Wheel retaining nut. When removing the Steering Wheel the specified Steering Wheel puller j-1859-a should be used because hammering at the end of the Steering Column shaft could loosen the plastic injections suggesting supports for the rigidity of the Steering Column. Mount the j 1859-a (J 1859-A) to the Steering Wheel, and then take out the Steering Wheel with a help of j 1859-a device. After removal, install the Steering Wheel on the Steering Shaft, then the Steering Wheel retaining nut followed by tightening it to 41 nm (30 ft. Lbs). Lastly, install the horn plunger to steering colum, the Steering Wheel inflator module and activate the restraints system.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the steering wheel on GMC Sonoma? Posted by Customer
    A:
    Steering Wheel replacement starts with disabling the sir system followed by inflator module removal. Press and hold the Steering Column's horn plunger towards its stop mark then rotate it 90 degrees clockwise. Disconnection of Steering Wheel electrical connections remains necessary for vehicles equipped with repeated Steering Wheel control systems. Before you reinstall the Steering Wheel keep the nut that holds the Steering Wheel to the Steering Shaft then make marks to align the Steering Wheel and Steering Shaft correctly. The j 1859-a (J 1859-A) Steering Wheel puller requires usage because striking the Steering Column shaft's end with a hammer might cause the plastic injections that hold the column steady to loosen. Detach the Steering Wheel while using j 1859-a (J 1859-A) on the wheel previously installed. Remove j 1859-a (J 1859-A) from the Steering Wheel. For new Steering Wheel installation start by setting your multifunction switch turn signal to neutral before matching the Steering Wheel's mark to the Steering Shaft. Then secure the Steering Wheel on the shaft. Fitting the Steering Wheel retaining nut requires torque to 41 nm or 30 ft. Lbs. A vehicle with redundant Steering Wheel controls needs its electrical connector reconnected first before users install the horn plunger and inflator module to enable the sir system.
    Posted by ChevyPartsGiant Specialist
    Q:
    What steps follow after tightening the retaining nut for the 2000 GMC Jimmy? Posted by Customer
    A:
    Reconnect the steering wheel electrical connector, install the horn plunger, and finally, install the inflator module before enabling the SIR system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Steering Wheel
    Q:
    What should be done with the nut that retains the steering wheel for the 2000 GMC Jimmy? Posted by Customer
    A:
    Remove the nut and mark the steering wheel to the steering wheel shaft for proper alignment during installation.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Steering Wheel
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Steering Wheel 15763216 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15763216 Steering Wheel is available in the market under the name GM Steering Wheel. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15763216 Steering Wheel fits certain Chevrolet S10, Tahoe, Silverado 1500 models, as well as GMC Sierra 1500, Yukon, Sierra 2500 HD. Additionally, it is compatible with Oldsmobile Bravada models.
The original GM component designated by manufacturer part number 15763216 maintains top performance when functioning as the Wheel, Steering unit. The component 15763216 is constructed from durable material and its dimensions span 21.9 x 20.3 x 11.2 inches while weighing 4.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 15763216 has available replacement options 16822251. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.