How to Replace Rear Brake Calipers on 2002 Chevrolet Monte Carlo?

Begin the rear brake caliper replacement by checking brake master cylinder fluid levels; if fluid exceeds midpoint between maximum-full and minimum levels drain fluid to reach this point. The fluid amount needs adjustment towards that midway point if the reservoir shows more than the middle of both maximum-full and minimum limits. First raise the vehicle while providing support and then remove both the tire and wheel assembly from the rear side. Use your hands to screw two wheel lug nuts until the rotor stays in place on the hub. You should use a large c-clamp to position over the brake caliper top against the outboard Brake Pad back surface. Tighten this clamp till the caliper piston pushes into the caliper bore enough to remove the caliper from the rotor. Extract the c-clamp and brake hose-to-caliper bolt while discarding the two existing copper brake hose gaskets. Use a piece of material to seal the rear brake hose opening followed by removal of the caliper bolts (1 and 3) along with the caliper from its position between the caliper bracket and rotor . When checking caliper bracket bolt boots you must replace every defective boot as well as inspect and replace damaged caliper bolts with new bushings and bolts. When installing the caliper position it over the rotor combined with caliper bracket after assuring correct placement of bushings. Validate the caliper bolts (1 and 3) by observing threads and then apply silicone grease along with lubricating the 2 bolt boots (13 and 4) residing in the caliper bracket. Fasten caliper bolts numbers 1 and 3 while making sure boot leather fits properly without causing damage and torque them to 44 nm (32 ft. Lbs.). Place the new copper brake hose gaskets onto the brake hose bolt followed by installing the brake hose-to-caliper bolt with a torque of 54 nm (40 ft. Lbs.). To complete the brake job reinstall the rear wheel and tire assembly after removing the rotor hub retaining lug nuts then lower the vehicle then fill the master cylinder to correct fluid level bleed the system and check the hydraulic brake system for leaks.

OEM 2002 Chevrolet Monte Carlo Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2002 Chevrolet Monte Carlo Caliper, Front Driver Side
Part Number: 18046196
$145.18 MSRP: $284.26
You Save: $139.08 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18029818
- Item Weight: 9.80 Pounds
- Item Dimensions: 9.5 x 8.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046196
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
2002 Chevrolet Monte Carlo Caliper
Part Number: 88965667
$76.17 MSRP: $231.41
You Save: $155.24 (68%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18029936
- Item Weight: 4.10 Pounds
- Item Dimensions: 8.1 x 6.2 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88965667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2002 Chevrolet Monte Carlo Caliper, Front Passenger Side
Part Number: 18046197
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18029819
- Item Weight: 10.40 Pounds
- Item Dimensions: 7.8 x 9.0 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046197
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
2002 Chevrolet Monte Carlo Caliper Overhaul Kit, Rear
Part Number: 18023387
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper Piston; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Item Weight: 0.40 Pounds
- Item Dimensions: 9.2 x 7.9 x 6.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18023387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
2002 Chevrolet Monte Carlo Caliper
Part Number: 88965666
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18029935
- Item Weight: 4.10 Pounds
- Item Dimensions: 8.2 x 6.3 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88965666
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2002 Chevrolet Monte Carlo Overhaul Kit, Front
Part Number: 18017156
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Wheel Brake Cylinder/Caliper Piston Kit.
- Position: Front
- Replaces: 18024958
- Item Weight: 0.30 Pounds
- Item Dimensions: 3.9 x 3.8 x 0.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 18017156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

2002 Chevrolet Monte Carlo Brake Calipers

With a comprehensive array of OEM 2002 Chevrolet Monte Carlo Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2002 Chevrolet Monte Carlo Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2002 Chevrolet Monte Carlo Parts Questions & Experts Answers

Q: How to Replace Rear Brake Calipers on 2002 Chevrolet Monte Carlo?
A: Begin the rear brake caliper replacement by checking brake master cylinder fluid levels; if fluid exceeds midpoint between maximum-full and minimum levels drain fluid to reach this point. The fluid amount needs adjustment towards that midway point if the reservoir shows more than the middle of both maximum-full and minimum limits. First raise the vehicle while providing support and then remove both the tire and wheel assembly from the rear side. Use your hands to screw two wheel lug nuts until the rotor stays in place on the hub. You should use a large c-clamp to position over the brake caliper top against the outboard Brake Pad back surface. Tighten this clamp till the caliper piston pushes into the caliper bore enough to remove the caliper from the rotor. Extract the c-clamp and brake hose-to-caliper bolt while discarding the two existing copper brake hose gaskets. Use a piece of material to seal the rear brake hose opening followed by removal of the caliper bolts (1 and 3) along with the caliper from its position between the caliper bracket and rotor . When checking caliper bracket bolt boots you must replace every defective boot as well as inspect and replace damaged caliper bolts with new bushings and bolts. When installing the caliper position it over the rotor combined with caliper bracket after assuring correct placement of bushings. Validate the caliper bolts (1 and 3) by observing threads and then apply silicone grease along with lubricating the 2 bolt boots (13 and 4) residing in the caliper bracket. Fasten caliper bolts numbers 1 and 3 while making sure boot leather fits properly without causing damage and torque them to 44 nm (32 ft. Lbs.). Place the new copper brake hose gaskets onto the brake hose bolt followed by installing the brake hose-to-caliper bolt with a torque of 54 nm (40 ft. Lbs.). To complete the brake job reinstall the rear wheel and tire assembly after removing the rotor hub retaining lug nuts then lower the vehicle then fill the master cylinder to correct fluid level bleed the system and check the hydraulic brake system for leaks.