How to replace the rear axle shaft on 2002 Chevrolet S10?

The vehicle should be raised before starting to replace rear axle shafts while you also remove tire and wheel assemblies. If your vehicle has these components you need to remove its brake caliper and Brake Drum. The next action involves removing both the rear cover and gasket before removing the pinion shaft locking bolt. Owners of axles without locking differentials should take off the pinion shaft first. Those with locking differentials should first remove the shaft's middle section before slowly rotating the case until the pinion shaft reaches the housing. A screwdriver-type tool helps you to turn the Differential case lock until it points directly at the thrust block. Use a tool to push the Axle Shaft flange toward the Differential after removing its c-lock from the button end. Important: avoid Axle Shaft rotation when removing it because this action might cause gear misalignment that makes reassembly more complicated. Extract the housing's Axle Shaft. During installation, manually position the Axle Shaft inside the rear axle housing so the splines can align with the Differential side gear. If your axle does not have a locking Differential then apply the lock on the button end of the Axle Shaft. C-lock users maintaining a partial position of the pinion shaft should align its ends with the thrust block while installing the c-lock on the Axle Shaft. Pull the shaft flange away from your body until the lock enters the Differential gear while aligning the pinion shaft's hole with the Differential case's screw hole. Thread the new pinion shaft locking bolt into position and torque it to 36 nm (27 ft. Lbs.). Put the brake caliper (if present) back first along with the gasket and rear cover and Brake Drum (if installed). Then return the tire-wheel assembly to its position. The correct fluid needs to be added to the rear axle portion before the vehicle reaches the floor.

OEM 2002 Chevrolet S10 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Axle Shafts found

View related parts
2002 Chevrolet S10 Axle Shaft, Rear Part Number: 26050549
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Item Weight: 15.70 Pounds
- Item Dimensions: 33.1 x 6.8 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26050549
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Assembly, Front Center Part Number: 15756008
Product Specifications
- Other Name: Axle, Front Axle And Axle Center; Differential; Axle Shaft; Differential Assembly
- Position: Front Center
- Replaces: 26046029
- Item Weight: 68.90 Pounds
- Item Dimensions: 26.8 x 18.5 x 13.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15756008
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Assembly, Rear Part Number: 15086716
Product Specifications
- Other Name: Axle, Rear Axle; Axle Shaft
- Position: Rear
- Replaces: 15081147
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15086716
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Assembly Part Number: 93720063
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Output Shaft; Shaft Kit, Front Axle
- Position: Front
- Replaces: 26055048
- Item Weight: 16.50 Pounds
- Item Dimensions: 6.3 x 6.4 x 28.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 93720063
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Assembly, Front Driver Side Part Number: 26055053
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Shaft Kit, Front Axle
- Position: Front Driver Side
- Item Weight: 17.30 Pounds
- Item Dimensions: 28.9 x 6.0 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26055053
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Assembly, Front Passenger Side Part Number: 26055049
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Shaft Kit, Front Axle
- Position: Front Passenger Side
- Item Weight: 16.50 Pounds
- Item Dimensions: 34.2 x 5.3 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26055049
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Shaft, Rear Part Number: 26064388
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Item Weight: 14.40 Pounds
- Item Dimensions: 29.4 x 6.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26064388
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Shafts, Rear Part Number: 26064387
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Item Weight: 14.30 Pounds
- Item Dimensions: 28.3 x 6.3 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26064387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Assembly, Front Driver Side Part Number: 26055052
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Output Shaft; Shaft Kit, Front Axle
- Position: Front Driver Side
- Item Weight: 19.40 Pounds
- Item Dimensions: 29.6 x 5.8 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26055052
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Shaft, Front Part Number: 26042726
Product Specifications
- Other Name: Shaft, Front Drive Axle Clutch; Output Shaft; Driven Shaft; Shaft, Front Axle
- Position: Front
- Item Weight: 2.00 Pounds
- Item Dimensions: 9.2 x 3.7 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26042726
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, Durango, EL, LS, Sport, Tahoe, Xtreme, ZR2, ZR5 | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Shaft, Front Driver Side Part Number: 26053318
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shafts; Shaft
- Position: Front Driver Side
- Item Weight: 4.30 Pounds
- Item Dimensions: 16.1 x 3.7 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26053318
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2002 Chevrolet S10 Axle Shafts, Rear Part Number: 26058079
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Item Weight: 16.10 Pounds
- Item Dimensions: 48.5 x 11.7 x 8.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26058079
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet S10 Submodels:
- Base, LS, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS

2002 Chevrolet S10 Axle Shaft

With a comprehensive array of OEM 2002 Chevrolet S10 Axle Shaft, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2002 Chevrolet S10 Axle Shaft are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2002 Chevrolet S10 Axle Shaft Parts and Q&A

Q: How to replace the rear axle shaft on 2002 Chevrolet S10?
A: The vehicle should be raised before starting to replace rear axle shafts while you also remove tire and wheel assemblies. If your vehicle has these components you need to remove its brake caliper and Brake Drum. The next action involves removing both the rear cover and gasket before removing the pinion shaft locking bolt. Owners of axles without locking differentials should take off the pinion shaft first. Those with locking differentials should first remove the shaft's middle section before slowly rotating the case until the pinion shaft reaches the housing. A screwdriver-type tool helps you to turn the Differential case lock until it points directly at the thrust block. Use a tool to push the Axle Shaft flange toward the Differential after removing its c-lock from the button end. Important: avoid Axle Shaft rotation when removing it because this action might cause gear misalignment that makes reassembly more complicated. Extract the housing's Axle Shaft. During installation, manually position the Axle Shaft inside the rear axle housing so the splines can align with the Differential side gear. If your axle does not have a locking Differential then apply the lock on the button end of the Axle Shaft. C-lock users maintaining a partial position of the pinion shaft should align its ends with the thrust block while installing the c-lock on the Axle Shaft. Pull the shaft flange away from your body until the lock enters the Differential gear while aligning the pinion shaft's hole with the Differential case's screw hole. Thread the new pinion shaft locking bolt into position and torque it to 36 nm (27 ft. Lbs.). Put the brake caliper (if present) back first along with the gasket and rear cover and Brake Drum (if installed). Then return the tire-wheel assembly to its position. The correct fluid needs to be added to the rear axle portion before the vehicle reaches the floor.