How to Replace the Front Axle Shaft (S4WD) Inner Shaft and Housing on 2003 Chevrolet S10?

Replacing front Axle Shaft (S4WD) inner shaft or housing starts with vehicle lifting. First disconnect the wheel Axle Shaft from the right side of the vehicle along with the Clutch Cable from the Clutch Fork. Begin by removing bolts and washers from the inner Axle Shaft housing before proceeding to remove the remaining two inner Axle Shaft housing to differential carrier assembly bolts. During removal make sure thrust washers and Clutch Fork sleeve remain secure with the inner Axle Shaft. Use a vise to clamp down the inner shaft housing before striking the inside of the Axle Shaft with a hammer and brass drift to extract the assembly from the Axle Shaft. Remove the Clutch Cable retainer spring followed by the Clutch Fork assembly then Clutch Fork inner spring and Clutch Fork sleeve and thrust washer and clutch gear. To replace the inner Axle Shaft bearing and seal insert them into the axle housing after using a punch tool to remove the clutch gear, thrust washer, inner Axle Shaft, and Clutch Fork seal. Use the j33799 Clutch Fork housing seal installer (J33799) to set the new Clutch Fork seal before placing the inner Axle Shaft inside the housing and adding the thrust washer. Secure the thrust washer with chassis grease. Drive the clutch gear onto the inner Axle Shaft by using a plastic hammer after installing the new retaining ring into the clutch gear. Afterward add the thrust washer together with Clutch Fork inner spring, Clutch Fork, Clutch Fork sleeve, and Clutch Cable retainer spring to the inner Axle Shaft housing. Sealant gm p/n 1052492 or its equivalent must be applied to the inner axle housing differential carrier interface before attaching the housing assembly to the differential carrier with finger-tight bolt placement at the 1 o'clock position then positioning the housing to install the 11 o'clock position bolt also finger tight. First install the Clutch Cable housing and Clutch Cable before using bolts and washers and nuts to secure the inner Axle Shaft housing to the frame bracket. Tighten the frame bracket nuts to 98 nm (72 ft. Lbs.) and the housing to differential carrier assembly bolts to 48 nm (36 ft. Lbs.). Last, install the right Axle Shaft then check the axle lubricant levels before lowering the vehicle.

OEM 2003 Chevrolet S10 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Axle Shafts found

View related parts
2003 Chevrolet S10 Axle Shaft, Rear Part Number: 26050549
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Item Weight: 15.70 Pounds
- Item Dimensions: 33.1 x 6.8 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26050549
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Assembly, Front Center Part Number: 15756008
Product Specifications
- Other Name: Axle, Front Axle And Axle Center; Differential; Axle Shaft; Differential Assembly
- Position: Front Center
- Replaces: 26046029
- Item Weight: 68.90 Pounds
- Item Dimensions: 26.8 x 18.5 x 13.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15756008
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Assembly, Rear Part Number: 15086716
Product Specifications
- Other Name: Axle, Rear Axle; Axle Shaft
- Position: Rear
- Replaces: 15081147
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15086716
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Assembly Part Number: 93720063
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Output Shaft; Shaft Kit, Front Axle
- Position: Front
- Replaces: 26055048
- Item Weight: 16.50 Pounds
- Item Dimensions: 6.3 x 6.4 x 28.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 93720063
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Assembly, Front Driver Side Part Number: 26055053
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Shaft Kit, Front Axle
- Position: Front Driver Side
- Item Weight: 17.30 Pounds
- Item Dimensions: 28.9 x 6.0 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26055053
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Assembly, Front Passenger Side Part Number: 26055049
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Shaft Kit, Front Axle
- Position: Front Passenger Side
- Item Weight: 16.50 Pounds
- Item Dimensions: 34.2 x 5.3 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26055049
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Shaft, Rear Part Number: 26064388
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Item Weight: 14.40 Pounds
- Item Dimensions: 29.4 x 6.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26064388
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Shafts, Rear Part Number: 26064387
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Item Weight: 14.30 Pounds
- Item Dimensions: 28.3 x 6.3 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26064387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Assembly, Front Driver Side Part Number: 26055052
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Output Shaft; Shaft Kit, Front Axle
- Position: Front Driver Side
- Item Weight: 19.40 Pounds
- Item Dimensions: 29.6 x 5.8 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26055052
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Shaft, Front Part Number: 26042726
Product Specifications
- Other Name: Shaft, Front Drive Axle Clutch; Output Shaft; Driven Shaft; Shaft, Front Axle
- Position: Front
- Item Weight: 2.00 Pounds
- Item Dimensions: 9.2 x 3.7 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26042726
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, Durango, EL, LS, Sport, Tahoe, Xtreme, ZR2, ZR5 | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Shaft, Front Driver Side Part Number: 26053318
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shafts; Shaft
- Position: Front Driver Side
- Item Weight: 4.30 Pounds
- Item Dimensions: 16.1 x 3.7 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26053318
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
2003 Chevrolet S10 Axle Shafts, Rear Part Number: 26058079
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Item Weight: 16.10 Pounds
- Item Dimensions: 48.5 x 11.7 x 8.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 26058079
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Chevrolet S10 Submodels:
- Base, LS, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS

2003 Chevrolet S10 Axle Shaft

With a comprehensive array of OEM 2003 Chevrolet S10 Axle Shaft, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2003 Chevrolet S10 Axle Shaft are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2003 Chevrolet S10 Axle Shaft Parts and Q&A

Q: How to Replace the Front Axle Shaft (S4WD) Inner Shaft and Housing on 2003 Chevrolet S10?
A: Replacing front Axle Shaft (S4WD) inner shaft or housing starts with vehicle lifting. First disconnect the wheel Axle Shaft from the right side of the vehicle along with the Clutch Cable from the Clutch Fork. Begin by removing bolts and washers from the inner Axle Shaft housing before proceeding to remove the remaining two inner Axle Shaft housing to differential carrier assembly bolts. During removal make sure thrust washers and Clutch Fork sleeve remain secure with the inner Axle Shaft. Use a vise to clamp down the inner shaft housing before striking the inside of the Axle Shaft with a hammer and brass drift to extract the assembly from the Axle Shaft. Remove the Clutch Cable retainer spring followed by the Clutch Fork assembly then Clutch Fork inner spring and Clutch Fork sleeve and thrust washer and clutch gear. To replace the inner Axle Shaft bearing and seal insert them into the axle housing after using a punch tool to remove the clutch gear, thrust washer, inner Axle Shaft, and Clutch Fork seal. Use the j33799 Clutch Fork housing seal installer (J33799) to set the new Clutch Fork seal before placing the inner Axle Shaft inside the housing and adding the thrust washer. Secure the thrust washer with chassis grease. Drive the clutch gear onto the inner Axle Shaft by using a plastic hammer after installing the new retaining ring into the clutch gear. Afterward add the thrust washer together with Clutch Fork inner spring, Clutch Fork, Clutch Fork sleeve, and Clutch Cable retainer spring to the inner Axle Shaft housing. Sealant gm p/n 1052492 or its equivalent must be applied to the inner axle housing differential carrier interface before attaching the housing assembly to the differential carrier with finger-tight bolt placement at the 1 o'clock position then positioning the housing to install the 11 o'clock position bolt also finger tight. First install the Clutch Cable housing and Clutch Cable before using bolts and washers and nuts to secure the inner Axle Shaft housing to the frame bracket. Tighten the frame bracket nuts to 98 nm (72 ft. Lbs.) and the housing to differential carrier assembly bolts to 48 nm (36 ft. Lbs.). Last, install the right Axle Shaft then check the axle lubricant levels before lowering the vehicle.