How to replace the front brake line on 2006 Chevrolet Uplander?

Start by raising the vehicle to work safely and remove the tire plus wheel assembly from their position. Wipe away dirt from brake hose fittings before adding a rubber plug to the open brake pipe fitting to avoid fluid loss. A flat-bladed tool releases the brake hose retainer from the brake hose so you can pull out the brake pipe fitting from the brake hose. First disconnect the brake hose bracket from its position then gently pull out the brake hose from its mounting point. Remove the brake hose bolt from the brake caliper before detaching the brake hose from the caliper. Insert a rubber stopper into the bolt opening on the brake caliper to hold fluid in while you get rid of the two copper brake hose gaskets that could stick when you separate them from the brace or end. To assemble install the prepared new copper brake hose gaskets onto the brake hose before attaching the brake hose bolt. Screw the brake hose bolt to 54 nm (40 ft. Lbs.) and make sure the hose flows straight without bends toward the brake hose bracket's notch. Set the brake hose on the bracket properly then fasten it through the hose retainer. Install the brake pipe fitting onto the brake hose before tightening it to 21 nm (15 ft. Lbs.) while keeping the rubber cap removed. Do not put the vehicle in motion before having full brake control due to air trapped in the brake system that may cause failure. Reinstall the tire and wheel assembly on the car and lower the vehicle after you bleed brake fluid from the caliper through the bleeder valve.

OEM 2006 Chevrolet Uplander Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Lines found

View related parts
2006 Chevrolet Uplander Flex Hose
Part Number: 15899075
$32.74 MSRP: $61.46
You Save: $28.72 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Item Weight: 1.30 Pounds
- Item Dimensions: 6.3 x 18.7 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15899075
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Flex Hose, Front Passenger Side
Part Number: 15899072
$29.76 MSRP: $53.85
You Save: $24.09 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 10305084, 15817953
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.2 x 2.0 x 18.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15899072
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Flex Hose, Passenger Side
Part Number: 15899074
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 15232836, 15222312
- Item Weight: 1.10 Pounds
- Item Dimensions: 19.1 x 6.8 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15899074
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Flex Hose, Driver Side
Part Number: 15899073
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaces: 15232835, 15222311
- Item Weight: 0.70 Pounds
- Item Dimensions: 14.0 x 8.0 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15899073
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Flex Hose, Rear
Part Number: 19366711
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 15899076
- Item Weight: 1.30 Pounds
- Item Dimensions: 9.4 x 3.1 x 10.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366711
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Flex Hose, Front
Part Number: 19366708
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Replaces: 10305083, 15899071
- Item Weight: 12.00 Pounds
- Item Dimensions: 5.2 x 2.1 x 12.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366708
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS

2006 Chevrolet Uplander Brake Line

With a comprehensive array of OEM 2006 Chevrolet Uplander Brake Line, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2006 Chevrolet Uplander Brake Line are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2006 Chevrolet Uplander Brake Line Parts Questions & Experts Answers

Q: How to replace the front brake line on 2006 Chevrolet Uplander?
A: Start by raising the vehicle to work safely and remove the tire plus wheel assembly from their position. Wipe away dirt from brake hose fittings before adding a rubber plug to the open brake pipe fitting to avoid fluid loss. A flat-bladed tool releases the brake hose retainer from the brake hose so you can pull out the brake pipe fitting from the brake hose. First disconnect the brake hose bracket from its position then gently pull out the brake hose from its mounting point. Remove the brake hose bolt from the brake caliper before detaching the brake hose from the caliper. Insert a rubber stopper into the bolt opening on the brake caliper to hold fluid in while you get rid of the two copper brake hose gaskets that could stick when you separate them from the brace or end. To assemble install the prepared new copper brake hose gaskets onto the brake hose before attaching the brake hose bolt. Screw the brake hose bolt to 54 nm (40 ft. Lbs.) and make sure the hose flows straight without bends toward the brake hose bracket's notch. Set the brake hose on the bracket properly then fasten it through the hose retainer. Install the brake pipe fitting onto the brake hose before tightening it to 21 nm (15 ft. Lbs.) while keeping the rubber cap removed. Do not put the vehicle in motion before having full brake control due to air trapped in the brake system that may cause failure. Reinstall the tire and wheel assembly on the car and lower the vehicle after you bleed brake fluid from the caliper through the bleeder valve.