How to replace the ABS Control Module on 2007 Buick LaCrosse?

The replacement of both the ABS Control Module (ABSCM) starts by flipping the ignition switch to off. In order to access the ABS Control Module the first step includes removing the fuel injector sight shield followed by removing the front fender upper diagonal brace along with the air cleaner intake duct. Unlatch the locking tab from the harness connector of the ABSCM then remove the harness itself. The assembly maintenance should start with cleaning away all dirt and debris before removing the 6 ABSCM to brake pressure modulator valve (BPMV) retaining bolt/screws. Do not separate the components as this leads to damage of both BPMV surfaces and solenoid valves. The BPMV and ABSCM separation begins after disconnecting the pump motor connector from its bottom ABSCM position. First install the pump motor connector to the ABSCM and then place the ABSCM onto the BPMV. Secure the 6 ABSCM to BPMV retaining bolt/screws by tightening them up to 2.9 N.m (26 lb in). Connect the ABSCM harness connector then return the locking tab to position. Put back all components including the air cleaner intake duct followed by the front fender upper diagonal brace and fuel injector sight shield if they were installed. Start the Diagnostic System Check - Vehicle while keeping the ignition key in the RUN position without engine activation. Check the Control Module References to find information about programming and setup.

OEM 2007 Buick LaCrosse ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 ABS Control Modules found

View related parts
2007 Buick LaCrosse Modulator Valve
Part Number: 19416842
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; Modulator; Valve, Electronic Brake Control
- Replaces: 15269563, 19121327
- Item Weight: 7.50 Pounds
- Item Dimensions: 9.2 x 7.4 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19416842
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Buick LaCrosse Submodels:
- CX, CXL | 6 Cyl 3.8 L GAS
View related parts
2007 Buick LaCrosse Modulator Valve
Part Number: 19416839
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode (W/Electronic Brake Control Module); Modulator; Valve, Electronic Brake Control
- Replaces: 15270028, 19152722
- Item Weight: 6.30 Pounds
- Item Dimensions: 9.5 x 7.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19416839
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Buick LaCrosse Submodels:
- CXS | 6 Cyl 3.6 L GAS
View related parts
2007 Buick LaCrosse Control Module
Part Number: 19302010
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 19121328
- Item Weight: 1.30 Pounds
- Item Dimensions: 9.4 x 6.1 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19302010
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Buick LaCrosse Submodels:
- CX, CXL | 6 Cyl 3.8 L GAS
View related parts
2007 Buick LaCrosse Control Module
Part Number: 19416829
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 10341579, 15269567, 19152725, 19301999, 19121334
- Item Weight: 2.30 Pounds
- Item Dimensions: 9.5 x 6.2 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19416829
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Buick LaCrosse Submodels:
- CXS | 6 Cyl 3.6 L GAS
View related parts
2007 Buick LaCrosse Control Module
Part Number: 19121330
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Item Weight: 1.30 Pounds
- Item Dimensions: 9.5 x 6.2 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19121330
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Buick LaCrosse Submodels:
- CXS | 6 Cyl 3.6 L GAS
View related parts
2007 Buick LaCrosse Modulator Valve
Part Number: 19416886
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode (W/Electronic Brake Control Module); Modulator; Valve, Electronic Brake Control
- Replaces: 19121329
- Item Weight: 8.90 Pounds
- Item Dimensions: 9.5 x 7.4 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19416886
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Buick LaCrosse Submodels:
- CXS | 6 Cyl 3.6 L GAS

2007 Buick LaCrosse ABS Control Module

With a comprehensive array of OEM 2007 Buick LaCrosse ABS Control Module, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2007 Buick LaCrosse ABS Control Module are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2007 Buick LaCrosse Parts Questions & Experts Answers

Q: How to replace the ABS Control Module on 2007 Buick LaCrosse?
A: The replacement of both the ABS Control Module (ABSCM) starts by flipping the ignition switch to off. In order to access the ABS Control Module the first step includes removing the fuel injector sight shield followed by removing the front fender upper diagonal brace along with the air cleaner intake duct. Unlatch the locking tab from the harness connector of the ABSCM then remove the harness itself. The assembly maintenance should start with cleaning away all dirt and debris before removing the 6 ABSCM to brake pressure modulator valve (BPMV) retaining bolt/screws. Do not separate the components as this leads to damage of both BPMV surfaces and solenoid valves. The BPMV and ABSCM separation begins after disconnecting the pump motor connector from its bottom ABSCM position. First install the pump motor connector to the ABSCM and then place the ABSCM onto the BPMV. Secure the 6 ABSCM to BPMV retaining bolt/screws by tightening them up to 2.9 N.m (26 lb in). Connect the ABSCM harness connector then return the locking tab to position. Put back all components including the air cleaner intake duct followed by the front fender upper diagonal brace and fuel injector sight shield if they were installed. Start the Diagnostic System Check - Vehicle while keeping the ignition key in the RUN position without engine activation. Check the Control Module References to find information about programming and setup.