How to replace the rear brake line on 2007 Chevrolet Impala?

Lift the car and position it properly before you take off the wheel and tire from the back. Wipe out all debris from brake hoses before putting a rubber stopper over the exposed brake pipe fitting. This maintains brake fluid quality. Put a back up wrench on the hose end to disconnect the brake pipe from the hose and seal the pipe brackets without damaging them. Pull the hose retaining clip off from its bracket and pull the hose out of the bracket. Detach the two copper brake hose gaskets from the brake caliper and brake hose ends before taking off the brake hose to caliper bolt and separating the brake hose from the brake caliper. Install both new copper brake hose gaskets and brake hose bolt onto the brake hose before fitting the parts onto the caliper. Secure the brake hose to caliper bolt onto the brake caliper by tightening it to 54 n.m (40 lb ft). When the vehicle rests on its suspension system you must align the brake hose paint stripe with the bracket notch by carefully positioning the hose into the bracket. Also normalize verbalization when possible. Put the retainer on the brake pipe fitting before attaching it to the brake hose through the back up wrench. To this end normalize verbalization when possible. Reposition the rear wheel and tire before installation and check if the hose touches suspension parts; replace the hose if necessary. End your work with brake system hydraulic bleeding followed by lowering the car.

OEM 2007 Chevrolet Impala Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Lines found

View related parts
2007 Chevrolet Impala Flex Hose, Front Passenger Side Part Number: 84393884
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 15242631
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.4 x 8.6 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84393884
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2007 Chevrolet Impala Flex Hose, Front Driver Side Part Number: 84393885
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 15242632
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.5 x 8.5 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84393885
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2007 Chevrolet Impala Flex Hose, Rear Driver Side Part Number: 19366667
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 15242630
- Item Weight: 0.70 Pounds
- Item Dimensions: 5.2 x 2.1 x 14.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2007 Chevrolet Impala Flex Hose, Passenger Side Part Number: 15242629
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 11.6 x 5.7 x 3.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15242629
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS

2007 Chevrolet Impala Brake Line

With a comprehensive array of OEM 2007 Chevrolet Impala Brake Line, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2007 Chevrolet Impala Brake Line are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2007 Chevrolet Impala Brake Line Parts and Q&A

Q: How to replace the rear brake line on 2007 Chevrolet Impala?
A: Lift the car and position it properly before you take off the wheel and tire from the back. Wipe out all debris from brake hoses before putting a rubber stopper over the exposed brake pipe fitting. This maintains brake fluid quality. Put a back up wrench on the hose end to disconnect the brake pipe from the hose and seal the pipe brackets without damaging them. Pull the hose retaining clip off from its bracket and pull the hose out of the bracket. Detach the two copper brake hose gaskets from the brake caliper and brake hose ends before taking off the brake hose to caliper bolt and separating the brake hose from the brake caliper. Install both new copper brake hose gaskets and brake hose bolt onto the brake hose before fitting the parts onto the caliper. Secure the brake hose to caliper bolt onto the brake caliper by tightening it to 54 n.m (40 lb ft). When the vehicle rests on its suspension system you must align the brake hose paint stripe with the bracket notch by carefully positioning the hose into the bracket. Also normalize verbalization when possible. Put the retainer on the brake pipe fitting before attaching it to the brake hose through the back up wrench. To this end normalize verbalization when possible. Reposition the rear wheel and tire before installation and check if the hose touches suspension parts; replace the hose if necessary. End your work with brake system hydraulic bleeding followed by lowering the car.