How to replace the front brake line on Chevrolet Impala?

To fix the front brake hose you need to lift and stabilize the car then take out the front tire and wheel. Use rubber plugs or caps on the brake pipe fitting to stop brake fluid from escaping or getting dirty and remove all foreign objects from the brake hose and pipe fittings. Hold the hose fitting tightly with a back up wrench and remove the brake pipe fitting from the brake hose. Cap or plug the brake pipe end to avoid damage while keeping the pipe and bracket at their original positions. Remove the brake hose retaining clip from the hose bracket for access to the mounting bracket. Pull out the brake hose from the bracket. You must take off the brake hose bolt from the brake caliper and then disconnect the brake hose from the caliper. Sever both brake hose gaskets from copper that adhers to brake caliper and hose ends. Debate the new copper brake hose gaskets and brake hose bolt onto brake hose before installing them into the brake caliper and fastening them at 54 n.m (40 lb ft). With the vehicle on its suspension use the brake hose paint stripe to position and push the hose through the bracket. Keep the hose free from kinks during the installation. Put the retainer into place on the hose end at the bracket before taking off the rubber plug or cap from the open brake pipe connection. Using a back up wrench on the hose fitting, join the brake pipe to the brake hose without bending the bracket and pipe. Secure the brake pipe fitting at 18 n.m (13 lb ft). Put back the front tire and wheel but check the hose stays clear of the suspension system at both extreme steering angles; fix the faulty position if the hose touches any part. Shift to the hydraulic brake mode then take fluid out before placing the car on a lower position.

How to replace the rear brake line on Chevrolet Impala?

You need to elevate the vehicle first and secure it properly before removing the tire and wheel assembly from the rear. Clear up all debris from brake hoses while you prepare the brake pipe fitting end with a rubber plug to block fluid loss and contamination. The brake pipe fitting disconnects from the brake hose using a backing wrench on the hose fitting while you place a cap or plug on the brake pipe fitting's end. Avoid bending the brake pipe or bracket during this process. Pull the retaining clip loose from the bracket holding the hose before detaching the hose from the bracket. Remove the brake hose to caliper bolt from the brake caliper before taking the brake hose off its mounting point on the caliper. Dispose of the two copper brake hose gaskets that might have stuck to either end of the caliper or the hose. To install the brake hose system use new copper brake hose gaskets then place them on together with brake hose bolt onto the brake hose . Fit the brake hose to caliper bolt onto the brake caliper and torque it to 54 nm (40 ft. Lbs.). After placing vehicle weight on the suspension system, install the brake hose into the bracket while checking for kinks and using the hose paint stripe to line up the fitting with the bracket notch. The hose fitting attaches to the bracket's retainer before you remove the rubber cap or plug from the end of the exposed brake pipe fitting. Use a back up wrench to connect the brake pipe fitting to the brake hose while avoiding bracket and pipe deformation and torque the brake pipe fitting to 15 nm (11 ft. Lbs.). Reinstall the rear tire and wheel assembly while maintaining hose clearance from all suspension components. Check the brake system operation after installation before removing the hose because any contact with suspension parts deserves correction. The vehicle needs final hydraulic brake system bleeding before lowering itself.

OEM Chevrolet Impala Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Brake Lines found

View related parts
Chevrolet Impala Brake Hose, Rear Part Number: 19173041
$13.65 MSRP: $24.38
You Save: $10.73 (45%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Line; Hose; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 09757655, 18031766, 9757655
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Flex Hose, Front Part Number: 19173093
$11.60 MSRP: $20.71
You Save: $9.11 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose; Hose, Hydraulic Brake
- Position: Front
- Replaces: 17999356, 18031819, 22113483
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Flex Hose, Front Part Number: 84025387
$15.64 MSRP: $29.35
You Save: $13.71 (47%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Replaces: 13327441, 20912237
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Flex Hose Part Number: 9757655
$13.65 MSRP: $24.38
You Save: $10.73 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Brake Rear; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaced by: 19173041
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Inlet Pipe Part Number: 22853692
$61.61 MSRP: $115.70
You Save: $54.09 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly-Power Brake Booster Pump Inlet; Pipe, Vacuum Power Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Impala | Eco | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Chevrolet Impala Flex Hose Part Number: 84025411
$15.98 MSRP: $30.00
You Save: $14.02 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaces: 13324942, 20912243
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Flex Hose, Front Driver Side Part Number: 22163577
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Flex Hose, Driver Side Part Number: 15876864
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaces: 22163799
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Flex Hose, Front Part Number: 22163414
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Flex Hose, Rear Part Number: 22111977
Product Specifications
- Other Name: Hose, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Flex Hose, Passenger Side Part Number: 15242629
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2011 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Flex Hose, Rear Driver Side Part Number: 19366667
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 15242630
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2011 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Flex Hose, Driver Side Part Number: 84393886
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaces: 20853705
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Flex Hose, Passenger Side Part Number: 15876863
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 22163798
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Flex Hose, Passenger Side Part Number: 84393887
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 20853704
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Flex Hose, Front Passenger Side Part Number: 84393884
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 15242631
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Flex Hose Part Number: 17999643
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Flex Hose Part Number: 17999642
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Flex Hose Part Number: 22111976
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Inlet Pipe Part Number: 22932262
Product Specifications
- Other Name: Pipe Assembly-Power Brake Booster Pump Inlet; Pipe, Vacuum Power Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Impala | LS, LT, LTZ | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

Chevrolet Impala Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Impala car Brake Line is vital component that ensures the smooth running and safe operation of the car brakes. Regardless of disc or drum brake system that your Impala car possesses, the brake lines and hoses have the function of providing brake fluid from the master cylinder to the calipers or the wheel cylinders. It is very important to pay close attention to the health of these components to avoid adverse events like the failure of brakes. Our online store specializes in Impala brake lines and hoses that are superior in quality and availably categorized according to your car's production year; thus, maintaining the right braking system with the right parts is made easy.

Chevrolet Impala Brake Line Parts and Q&A

Flex Hose, Passenger Side
15242629
Q: How to replace the front brake line on Chevrolet Impala?
A:
To fix the front brake hose you need to lift and stabilize the car then take out the front tire and wheel. Use rubber plugs or caps on the brake pipe fitting to stop brake fluid from escaping or getting dirty and remove all foreign objects from the brake hose and pipe fittings. Hold the hose fitting tightly with a back up wrench and remove the brake pipe fitting from the brake hose. Cap or plug the brake pipe end to avoid damage while keeping the pipe and bracket at their original positions. Remove the brake hose retaining clip from the hose bracket for access to the mounting bracket. Pull out the brake hose from the bracket. You must take off the brake hose bolt from the brake caliper and then disconnect the brake hose from the caliper. Sever both brake hose gaskets from copper that adhers to brake caliper and hose ends. Debate the new copper brake hose gaskets and brake hose bolt onto brake hose before installing them into the brake caliper and fastening them at 54 n.m (40 lb ft). With the vehicle on its suspension use the brake hose paint stripe to position and push the hose through the bracket. Keep the hose free from kinks during the installation. Put the retainer into place on the hose end at the bracket before taking off the rubber plug or cap from the open brake pipe connection. Using a back up wrench on the hose fitting, join the brake pipe to the brake hose without bending the bracket and pipe. Secure the brake pipe fitting at 18 n.m (13 lb ft). Put back the front tire and wheel but check the hose stays clear of the suspension system at both extreme steering angles; fix the faulty position if the hose touches any part. Shift to the hydraulic brake mode then take fluid out before placing the car on a lower position.
Flex Hose, Driver Side
15876864
Q: How to replace the rear brake line on Chevrolet Impala?
A:
You need to elevate the vehicle first and secure it properly before removing the tire and wheel assembly from the rear. Clear up all debris from brake hoses while you prepare the brake pipe fitting end with a rubber plug to block fluid loss and contamination. The brake pipe fitting disconnects from the brake hose using a backing wrench on the hose fitting while you place a cap or plug on the brake pipe fitting's end. Avoid bending the brake pipe or bracket during this process. Pull the retaining clip loose from the bracket holding the hose before detaching the hose from the bracket. Remove the brake hose to caliper bolt from the brake caliper before taking the brake hose off its mounting point on the caliper. Dispose of the two copper brake hose gaskets that might have stuck to either end of the caliper or the hose. To install the brake hose system use new copper brake hose gaskets then place them on together with brake hose bolt onto the brake hose . Fit the brake hose to caliper bolt onto the brake caliper and torque it to 54 nm (40 ft. Lbs.). After placing vehicle weight on the suspension system, install the brake hose into the bracket while checking for kinks and using the hose paint stripe to line up the fitting with the bracket notch. The hose fitting attaches to the bracket's retainer before you remove the rubber cap or plug from the end of the exposed brake pipe fitting. Use a back up wrench to connect the brake pipe fitting to the brake hose while avoiding bracket and pipe deformation and torque the brake pipe fitting to 15 nm (11 ft. Lbs.). Reinstall the rear tire and wheel assembly while maintaining hose clearance from all suspension components. Check the brake system operation after installation before removing the hose because any contact with suspension parts deserves correction. The vehicle needs final hydraulic brake system bleeding before lowering itself.