How to replace the Brake Proportioning Valve on Chevrolet Impala?

Washing the proportioning valve is forbidden because its internal components arrive with specific grease already in place. Start the repair by removing both the bracket from the master cylinder followed by the master cylinder reservoir. Use needle nose pliers to remove proportioning valve caps together with O-rings , springs , and proportioning valve pistons while making sure to protect the piston stems. Check the pistons for signs of corrosion and deformation before changing any damaged parts. Use clean denatured alcohol to sanitize all pieces then use non-lubricated compressed air for drying. When replacing the components use the silicone grease from the repair kit to lubricate the O-rings together with proportioning valve seals and proportioning valve piston stems. Install the new proportioning valve piston seals by positioning the lip seals upward and install the components into the master cylinder body. Position the springs inside the master cylinder body while placing new O-rings in the proportioning valve cap grooves. Tighten the proportioning valve caps to 27 Nm (20 ft. lbs.) torque specification.Replace the bracket to both the master cylinder and the master cylinder reservoir afterward. Finally, bleed the brakes.

OEM Chevrolet Impala Brake Proportioning Valve

Proportioning Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Proportioning Valves found

View related parts
Chevrolet Impala Pressure Metering Valve
Part Number: 18014469
$13.11 MSRP: $16.23
You Save: $3.12 (20%)
ADD TO CART
Product Specifications
- Other Name: Brake Proportioning Valve; Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Impala | Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Modulator Valve
Part Number: 15923034
Product Specifications
- Other Name: Valve, Electronic Brake Control; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2011 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Pressure Metering Valve
Part Number: 25509419
Product Specifications
- Other Name: Valve, Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Modulator Valve
Part Number: 15903776
Product Specifications
- Other Name: Valve, Electronic Brake Control; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Impala | LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Pressure Valve
Part Number: 12455422
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; ABS Control Module; Modulator Valve; Modulator; Valve, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Pressure Metering Valve
Part Number: 10289556
Product Specifications
- Other Name: Valve Assembly-Brake Proportioning; Brake Proportioning Valve; Valve, Brake Master Cylinder Proportioning
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Chevrolet Impala | Base, LS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Modulator Valve
Part Number: 10282600
Product Specifications
- Other Name: Valve, Electronic Brake Control; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Pressure Metering Valve
Part Number: 10223533
Product Specifications
- Other Name: Valve Assembly-Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS

Chevrolet Impala Brake Proportioning Valve

Our website offers an extensive catalog of genuine Chevrolet Impala Brake Proportioning Valve at unbeatable prices. Every OEM Chevrolet Impala Brake Proportioning Valve comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Impala Brake Proportioning Valve Parts Questions & Experts Answers

Pressure Metering Valve
18014469
Q: How to replace the Brake Proportioning Valve on Chevrolet Impala?
A: Washing the proportioning valve is forbidden because its internal components arrive with specific grease already in place. Start the repair by removing both the bracket from the master cylinder followed by the master cylinder reservoir. Use needle nose pliers to remove proportioning valve caps together with O-rings , springs , and proportioning valve pistons while making sure to protect the piston stems. Check the pistons for signs of corrosion and deformation before changing any damaged parts. Use clean denatured alcohol to sanitize all pieces then use non-lubricated compressed air for drying. When replacing the components use the silicone grease from the repair kit to lubricate the O-rings together with proportioning valve seals and proportioning valve piston stems. Install the new proportioning valve piston seals by positioning the lip seals upward and install the components into the master cylinder body. Position the springs inside the master cylinder body while placing new O-rings in the proportioning valve cap grooves. Tighten the proportioning valve caps to 27 Nm (20 ft. lbs.) torque specification.Replace the bracket to both the master cylinder and the master cylinder reservoir afterward. Finally, bleed the brakes.

Related Chevrolet Impala Parts

Browse Chevrolet Impala Brake Proportioning Valve by Years

2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1996 1995 1994 1985 1984