How to replace the front wheel bearing and hub on 2007 Chevrolet Impala?

Raise the vehicle and start to replace the front Wheel Bearing hub assembly. Take off the tire and wheel. Disconnect the Wheel Speed Sensor electric wire if present then unfasten the bracket. Insert a drift into the caliper and rotor through the nut opening as you take off the front wheel drive shaft nut. Place the j 42129 Wheel Hub remover tool at the Wheel Bearing and hub. Thread three wheel nuts and fasten them to the j 42129. Push the wheel drive shaft out using the j 42129 device and take off the Wheel Bearing/hub bolts before removing the j 42129 to keep the wheel drive shaft outer seal/boot safe and undamaged. When you remove the wheel suspension parts observe where the shield must go back. To install the new Wheel Bearing/hub place it with the splash shield in its proper position from removal while replacing any loose or removed fasteners to retain vehicle control. Reassemble both Wheel Bearing/hub bolts and torque them to 130 n.m (96 lb ft) of force. Reinstall the Brake Disc and caliper assembly before fastening the front wheel drive shaft nut with a drift tool to immobilize the rotor. Tighten to a torque of 190 n.m (140 lb.ft). When mounting the Wheel Speed Sensor electrical connector select the bracket if the vehicle configuration demands it and insert the connector into its designated spot on the bracket. Put on the tire and wheel after lowering the vehicle.

OEM 2007 Chevrolet Impala Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Wheel Bearings found

View related parts
2007 Chevrolet Impala Hub & Bearing, Rear
Part Number: 13585741
$178.89 MSRP: $320.88
You Save: $141.99 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Rear Wheel; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing Assembly; Hub, Rear Wheel
- Position: Rear
- Item Weight: 11.10 Pounds
- Item Dimensions: 9.5 x 8.2 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 13585741
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2007 Chevrolet Impala Hub Assembly, Front
Part Number: 84641365
$217.28 MSRP: $425.44
You Save: $208.16 (49%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Assembly, Front Wheel (W/Wheel Speed Sensor); Front Hub & Bearing; Front Wheel Hub Kit; Rear Wheel Hub
- Position: Front
- Replaced by: 19433930
- Item Weight: 10.20 Pounds
- Condition: New
- SKU: 84641365
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2007 Chevrolet Impala Front Hub & Bearing
Part Number: 88964096
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Bearing & Hub Repair Kit; Axle Bearing.; Hub & Bearing; Hub; Hub, Front Wheel
- Position: Front
- Replaces: 89047803, 12413005, 12413097
- Item Weight: 8.50 Pounds
- Item Dimensions: 7.0 x 7.0 x 6.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 88964096
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, Base, LS, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2007 Chevrolet Impala Hub & Bearing, Rear
Part Number: 19122338
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub; Axle Bearing; Wheel Hub; Hub & Bearing Assembly; Hub, Rear Wheel
- Position: Rear
- Replaces: 12413099
- Item Weight: 8.80 Pounds
- Item Dimensions: 7.4 x 7.1 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19122338
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Impala Submodels:
- 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS

2007 Chevrolet Impala Wheel Bearing

With a comprehensive array of OEM 2007 Chevrolet Impala Wheel Bearing, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2007 Chevrolet Impala Wheel Bearing are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2007 Chevrolet Impala Wheel Bearing Parts Questions & Experts Answers

Q: How to replace the front wheel bearing and hub on 2007 Chevrolet Impala?
A: Raise the vehicle and start to replace the front Wheel Bearing hub assembly. Take off the tire and wheel. Disconnect the Wheel Speed Sensor electric wire if present then unfasten the bracket. Insert a drift into the caliper and rotor through the nut opening as you take off the front wheel drive shaft nut. Place the j 42129 Wheel Hub remover tool at the Wheel Bearing and hub. Thread three wheel nuts and fasten them to the j 42129. Push the wheel drive shaft out using the j 42129 device and take off the Wheel Bearing/hub bolts before removing the j 42129 to keep the wheel drive shaft outer seal/boot safe and undamaged. When you remove the wheel suspension parts observe where the shield must go back. To install the new Wheel Bearing/hub place it with the splash shield in its proper position from removal while replacing any loose or removed fasteners to retain vehicle control. Reassemble both Wheel Bearing/hub bolts and torque them to 130 n.m (96 lb ft) of force. Reinstall the Brake Disc and caliper assembly before fastening the front wheel drive shaft nut with a drift tool to immobilize the rotor. Tighten to a torque of 190 n.m (140 lb.ft). When mounting the Wheel Speed Sensor electrical connector select the bracket if the vehicle configuration demands it and insert the connector into its designated spot on the bracket. Put on the tire and wheel after lowering the vehicle.