How to replace the rear brake line on Buick Park Avenue?

Start the brake hose replacement by lifting the vehicle and using tools to detach its wheel and tire. Before starting remove dirt from the brake hose and brake pipe connecting parts. Install a rubber cap to seal the exposed end of the brake pipe to keep fluid secure. Pull the brake pipe from the hose connection and apply a cap to the exposed end of the fitting. Use a flat tool to take off the brake hose retainer before pulling out the brake hose from its bracket and then removing the brake hose to caliper bolt from the brake caliper. Finally, extract the brake hose. Throw away the two brake hose gaskets because they may bond to the caliper or hose connection and add a rubber plug to the caliper bolt opening on the brake hose. To install the new unit use new copper brake hose gaskets and remove the existing rubber plug. Put new gaskets on the brake hose before attaching the bolt. Install the hose to the caliper bolt on the brake caliper while tightening it to 44 nm with 2 turns past hand tight. Verify no bends or twists exist in the brake hose. Put the brake hose onto the bracket and connect the brake hose retainer before taking off the rubber cap from the end of the brake pipe. Route the brake pipe into the brake hose and tighten it to 15 nm before bleeding the brake system to install the tire and wheel below the vehicle again.

How to replace the front brake line on Buick Park Avenue?

Start by lifting and holding your vehicle then removing its front wheel and tire. Remove any dirt or foreign material from the brake hose and pipes by properly cleaning them. Brake fluid loss and contamination in the system require you to put on a rubber cover at the brake pipe opening. Twist the brake hose away from the brake pipe fitting and put a fitting cap on it. Take out the brake hose by pushing its retainer with a flat-bladed tool before removing the bracket. Set the brake caliper aside and take off the brake hose to caliper bolt from the brake caliper while you discard the two stuck copper brake hose gaskets. Protect the brake pipe fitting with an extra cap to stop the fluid from leaking. Push a rubber plug into the brake caliper bolt opening of the brake hose before removing it. Place new copper brake hose gaskets onto the parts and link the brake hose assembly to the brake caliper after fastening the bolt at 44 nm (32 ft. Lbs.). Keep the brake hose straight when putting it into place. Connect the brake hose to its bracket using the retainer before taking off the rubber connector from the brake pipe end. Secure the brake hose fittings with 9 nm force while adding the bracket and bolt set to the strut assembly and tightening it to 13 nm. Close the Brake Line system fluid before putting back the tire and wheel assembly while lowering the vehicle.

OEM Buick Park Avenue Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Brake Lines found

View related parts
Buick Park Avenue Pressure Hose Part Number: 25528398
$30.86
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Brake Master Cylinder; Hydraulic Hose; Lower Pressure Hose; Hose, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Front Driver Side Part Number: 19173695
$22.52 MSRP: $40.21
You Save: $17.69 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Driver Side
- Replaces: 18032450
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Brake Hose, Front Passenger Side Part Number: 19174782
$31.66 MSRP: $56.54
You Save: $24.88 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Line
- Position: Front Passenger Side
- Replaces: 19111276, 18038998
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Brake Hose, Driver Side Part Number: 19111275
$31.75 MSRP: $56.70
You Save: $24.95 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Line
- Position: Driver Side
- Replaces: 18039012
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Front Passenger Side Part Number: 18032449
$29.16 MSRP: $52.08
You Save: $22.92 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose Part Number: 22113234
$15.37 MSRP: $30.86
You Save: $15.49 (51%)
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue High Pressure Hose Part Number: 25528384
Product Specifications
- Other Name: Hose; Hydraulic Hose; Pressure Hose; Hose, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose Part Number: 25522287
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose Part Number: 22113235
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Front Passenger Side Part Number: 19366761
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 22163448, 17999966, 22163886
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Front Driver Side Part Number: 19366760
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 22163885, 22163447, 17999817
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Rear Part Number: 19366759
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 17999820, 22163668, 22113390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Driver Side Part Number: 17999819
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaced by: 25694864
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Rear Part Number: 17999714
Product Specifications
- Other Name: Hose, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Front Driver Side Part Number: 17999713
Product Specifications
- Other Name: Hose Assembly-Front Brake (Left); Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Flex Hose, Front Passenger Side Part Number: 17999712
Product Specifications
- Other Name: Hose Assembly-Front Brake (Right); Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS

Buick Park Avenue Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Park Avenue parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Park Avenue Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Brake Line is one of the vital parts of the Buick Park Avenue series, which portrays the car's faithfulness and power. This Brake Line is tasked with moving the brake fluid from the master cylinder to the brake caliper pistons thus enabling the hydraulic brake system. Being one of the primary components of the Buick Park Avenue's brake system, the Brake Line is built to last while at the same time helping the vehicle run more effectively and safely than before. Whether in Buick Park Avenue of the old model or the improved models on the market, this brake kit guarantees efficient delivery in each of the models. The Brake Line is not just an ordinary line that runs through the car; it actually serves a very important purpose of not allowing the fluid leaks and for sustaining the hydraulic pressure which are so important for safe driving. Among the unique options, corrosion resistance of the used materials, as well as the availability of using upgraded metal hoses, including the Brake Line, reduces the braking delay and increases the sensitivity of the pedal, especially when performing stunts. Starting from 1975, Buick Park Avenue is one of the most popular cars that are characterized by their luxury and reliability The Brake Line represents one of the safety and performance traditions of Buick. From city drive to long distance highway drive, Brake Line adds to the confidence of the driver regarding the reliability of the braking system of the car and adds to the refinement of the Buick Park Avenue.

Buick Park Avenue Brake Line Parts and Q&A

Flex Hose, Rear
19366759
Q: How to replace the rear brake line on Buick Park Avenue?
A:
Start the brake hose replacement by lifting the vehicle and using tools to detach its wheel and tire. Before starting remove dirt from the brake hose and brake pipe connecting parts. Install a rubber cap to seal the exposed end of the brake pipe to keep fluid secure. Pull the brake pipe from the hose connection and apply a cap to the exposed end of the fitting. Use a flat tool to take off the brake hose retainer before pulling out the brake hose from its bracket and then removing the brake hose to caliper bolt from the brake caliper. Finally, extract the brake hose. Throw away the two brake hose gaskets because they may bond to the caliper or hose connection and add a rubber plug to the caliper bolt opening on the brake hose. To install the new unit use new copper brake hose gaskets and remove the existing rubber plug. Put new gaskets on the brake hose before attaching the bolt. Install the hose to the caliper bolt on the brake caliper while tightening it to 44 nm with 2 turns past hand tight. Verify no bends or twists exist in the brake hose. Put the brake hose onto the bracket and connect the brake hose retainer before taking off the rubber cap from the end of the brake pipe. Route the brake pipe into the brake hose and tighten it to 15 nm before bleeding the brake system to install the tire and wheel below the vehicle again.
Flex Hose, Front Driver Side
19366760
Q: How to replace the front brake line on Buick Park Avenue?
A:
Start by lifting and holding your vehicle then removing its front wheel and tire. Remove any dirt or foreign material from the brake hose and pipes by properly cleaning them. Brake fluid loss and contamination in the system require you to put on a rubber cover at the brake pipe opening. Twist the brake hose away from the brake pipe fitting and put a fitting cap on it. Take out the brake hose by pushing its retainer with a flat-bladed tool before removing the bracket. Set the brake caliper aside and take off the brake hose to caliper bolt from the brake caliper while you discard the two stuck copper brake hose gaskets. Protect the brake pipe fitting with an extra cap to stop the fluid from leaking. Push a rubber plug into the brake caliper bolt opening of the brake hose before removing it. Place new copper brake hose gaskets onto the parts and link the brake hose assembly to the brake caliper after fastening the bolt at 44 nm (32 ft. Lbs.). Keep the brake hose straight when putting it into place. Connect the brake hose to its bracket using the retainer before taking off the rubber connector from the brake pipe end. Secure the brake hose fittings with 9 nm force while adding the bracket and bolt set to the strut assembly and tightening it to 13 nm. Close the Brake Line system fluid before putting back the tire and wheel assembly while lowering the vehicle.