How to replace the outer CV Joint and seal on Buick Regal?

To replace the wheel drive shaft outer joint and seal, unscrew the large single retaining clamp from the CV Joint with a side cutter and discard it. Cut away the swage ring with hand grinder and take that off before you take the halfshaft outboard seal off of the CV Joint outer race at the big diameter. Push the boot away from the joint along its halfshaft bar and clean the face of the CV Joint inner race from grease. Remove the old outboard boot by using j 8059 (Snap Ring Pliers), spread the ears on the race retaining ring. Then pull cv-joint assembly out from the halfshaft bar. Tapping gently on a brass drift will switch the CV Joint cage and displace all six chrome alloy balls. Clean the inner and outer race assemblies, the CV Joint cage, and chrome alloy balls to remove all old grease and contaminants, followed by drying all parts and inspecting the CV Joint assembly for unusual wear, cracks, or damage, with replacement of damaged parts. Clean the halfshaft bar using the wire brush to remove rust around the mounting area of the seal. For assembly install a new swage ring on the neck of the out board boot and do not swager it then place the boot on the half shaft bar that is in the seal groove. Position the two pin shaft halves without the use of shims or any other interference-fit device, and swage the ring by placing the two parts together, and tightening the bolts to the hand-tight tolerance, alternately between each bolt using j 41048 (Small Swage Tool). Inspect the swaged ring for deformations and re-swage wherever required. Lightly grease with service kit grease in the ball grooves of the inner and outer races, then install the inner race into the cage taking care to ensure correct alignment. Put the cage and inner race into the outer cage, pop in chrome balls, fill the CV Joint with grease. Push the CV Joint onto the halfshaft bar all the way until the retaining ring is seated while assuring that the outboard boot is no dimpled or stretched. Slide the outboard boot with the large seal retaining clamp over the CV Joint outer race and crimp the clamp using j 35910 (Seal Clamp Tool) to 174 nm (130 ft. Lbs), checking the gap dimension on the clamp ear neuveau-steel tightening as necessary.

OEM Buick Regal CV Joint

CV Joint Axle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 CV Joints found

View related parts
Buick Regal Inner CV Joint, Front Driver Side Part Number: 13333930
$93.52 MSRP: $148.48
You Save: $54.96 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2017 Buick Regal | Base, CXL, GS, Premium, Sport Touring | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal Outer CV Joint, Front Part Number: 13296184
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Outer Joint
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2017 Buick Regal | Base, GS, Premium, Sport Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal Outer CV Joint, Front Part Number: 13296187
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; Outer Joint
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2017 Buick Regal | Base, CXL, GS, Premium, Sport Touring | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal C.V. Joint, Outer Part Number: 19148843
Product Specifications
- Other Name: Outer CV Joint; CV Joint; CV Joints; Outer Joint; Outer Joint Assembly
- Position: Outer
- Replaces: 26044408, 26075595
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Buick Regal | 25th Anniversary Edition, GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal C.V. Joint, Outer Part Number: 19122437
Product Specifications
- Other Name: Outer CV Joint; CV Joint; CV Joints; Outer Joint; Outer Joint Assembly
- Position: Outer
- Replaces: 26044410, 26045070
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2004 Buick Regal | GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Inner CV Joint, Front Driver Side Part Number: 26044402
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Buick Regal | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Inner CV Joint, Front Passenger Side Part Number: 26073379
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Tripod
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Buick Regal | GS, GSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Inner CV Joint, Front Passenger Side Part Number: 26062632
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Passenger Side
- Replaces: 26045071
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Buick Regal | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 3.8 L GAS
View related parts
Buick Regal CV Joints, Front Passenger Side Part Number: 26073375
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Buick Regal | GS, GSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal CV Joints, Front Part Number: 26073382
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Buick Regal | LS, LSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal CV Joints, Front Driver Side Part Number: 26073376
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Driver Side
- Replaces: 26073378
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Buick Regal | GS, GSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal CV Joints, Front Part Number: 26073381
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Buick Regal | LS, LSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal CV Joints, Front Part Number: 13333931
$95.85 MSRP: $150.14
You Save: $54.29 (37%)
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2017 Buick Regal | Base, CXL, GS, Premium, Sport Touring | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal CV Joints, Inner Part Number: 39196365
$104.07 MSRP: $163.02
You Save: $58.95 (37%)
Product Specifications
- Other Name: Inner CV Joint; Outer CV Joint; Outer Joint; Joint Kit, Front Wheel Drive Axle
- Position: Inner
- Replaces: 13333929
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2017 Buick Regal | Base, CXL, Premium | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal Inner CV Joint, Front Part Number: 13296195
$117.61 MSRP: $185.07
You Save: $67.46 (37%)
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; Inner Joint
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2016 Buick Regal | Base, CXL, GS, Premium, Sport Touring | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal Housing Assembly, Front Driver Side Part Number: 26062354
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Inner Joint Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Buick Regal | GS, LS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal CV Joints, Front Part Number: 26044412
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Joint Assembly; Tripod Housing; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1998 Buick Regal | Custom, Gran Sport, Limited, LS | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Inner CV Joint, Front Passenger Side Part Number: 26025700
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Joint Assembly; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Inner CV Joint, Front Driver Side Part Number: 26025701
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Inner CV Joint, Front Passenger Side Part Number: 26045744
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Tripod
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Regal | 25th Anniversary Edition, GS, LS | 6 Cyl 3.8 L GAS

| Page 1 of 2 |Next >

1-20 of 26 Results

Buick Regal CV Joint

Want to cut long-term maintenance and repair costs? Choose OEM CV Joint. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Regal parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Regal CV Joint includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Each part that is produced by the Buick brand is highly dependable and the Buick Regal CV Joint is no exception. Being one of the few points in a vehicle's transmission that allow the power to be transferred directly from the transmission to the wheels, the CV Joint is critical for both front-wheel-drive Buick Regal models and the regal rear-wheel-drive models. Rzeppa, tripod, as well as, the double offset joints are available for the Buick Regal model, and each of them is designed for providing a constant velocity depending on the angles of operation enhancing the smooth handling and dynamic performance. The longevity of those joints is further ensured by flexible rubber like seals which are stuffed with lubricant to shield the joints from contaminants and wear. In fact, this powertrain is associated with the brand's reliability, and thus, proper inspection of these boots is vital for the longevity of the CV Joint of the Buick Regal. The fact that the Buick Regal CV Joint integrates with several Regal models from the traditional luxury coupe car, the modern liftback sedan car, to the recently developed TourX station wagon shows the card's flexibility. They not only make the car more efficient but also play a very essential role of providing safety by ensuring the car handle stably and responsively. The CV Joint is considered to as premium with special engineering and high quality materials making it a favorite of drivers of Buick Regal cars who are in search of power and reliability in their cars.

Buick Regal CV Joint Parts Questions & Experts Answers

C.V. Joint, Outer
19122437
Q: How to replace the outer CV Joint and seal on Buick Regal?
A:
To replace the wheel drive shaft outer joint and seal, unscrew the large single retaining clamp from the CV Joint with a side cutter and discard it. Cut away the swage ring with hand grinder and take that off before you take the halfshaft outboard seal off of the CV Joint outer race at the big diameter. Push the boot away from the joint along its halfshaft bar and clean the face of the CV Joint inner race from grease. Remove the old outboard boot by using j 8059 (Snap Ring Pliers), spread the ears on the race retaining ring. Then pull cv-joint assembly out from the halfshaft bar. Tapping gently on a brass drift will switch the CV Joint cage and displace all six chrome alloy balls. Clean the inner and outer race assemblies, the CV Joint cage, and chrome alloy balls to remove all old grease and contaminants, followed by drying all parts and inspecting the CV Joint assembly for unusual wear, cracks, or damage, with replacement of damaged parts. Clean the halfshaft bar using the wire brush to remove rust around the mounting area of the seal. For assembly install a new swage ring on the neck of the out board boot and do not swager it then place the boot on the half shaft bar that is in the seal groove. Position the two pin shaft halves without the use of shims or any other interference-fit device, and swage the ring by placing the two parts together, and tightening the bolts to the hand-tight tolerance, alternately between each bolt using j 41048 (Small Swage Tool). Inspect the swaged ring for deformations and re-swage wherever required. Lightly grease with service kit grease in the ball grooves of the inner and outer races, then install the inner race into the cage taking care to ensure correct alignment. Put the cage and inner race into the outer cage, pop in chrome balls, fill the CV Joint with grease. Push the CV Joint onto the halfshaft bar all the way until the retaining ring is seated while assuring that the outboard boot is no dimpled or stretched. Slide the outboard boot with the large seal retaining clamp over the CV Joint outer race and crimp the clamp using j 35910 (Seal Clamp Tool) to 174 nm (130 ft. Lbs), checking the gap dimension on the clamp ear neuveau-steel tightening as necessary.