How to service and repair the exhaust crossover exhaust pipe on Cadillac Seville?

The first step for servicing the exhaust crossover pipe requires removal of the transaxle assembly. The service begins with removing the two bolts which secure the left side Exhaust Manifold. Replacment of the egr valve inlet pipe is necessary after disconnecting it because the water crossover uses a crush seal connection. Remove both the egr inlet pipe from the exhaust crossover before taking off the exhaust front pipe. The service procedure begins by unfastening the bolt connecting the crossover pipe to the crankcase then the nut securing the ignition module ground wire to the Cylinder Head and finishing with the bolt holding the crossover pipe to the Cylinder Head. Clear the crossover pipe from the engine compartment as the next step. Begin by applying two flange seals to the crossover pipe before positioning it correctly while keeping the lh Exhaust Manifold joint free from tightening. Install the exhaust front pipe after supporting it with hand torques to support bolts 1 and 3. Fasten the Cylinder Head support bolt at 25 nm (18 ft. Lbs.) while the crankcase support bolt requires the same torque setting of 25 nm (18 ft. Lbs.). Install the nut which supports the ignition module ground wire on the Cylinder Head before securing it with 17 nm torque value (13 ft. Lbs.). Secure all fasteners by tightening left hand Exhaust Manifold bolts to 25 nm (18 ft. Lbs.). Start the fitting of the egr inlet pipe-to-crossover valve with your hand to avoid threading issues before tightening it to 60 nm (44 ft. Lbs.). Finally, reinstall the transaxle assembly.

How to replace the Front Exhaust Pipe on Cadillac Seville?

Safety precautions for hot exhaust systems and removing exhaust parts should be followed before initiatives to replace the front Exhaust Manifold pipe begin. The repair process begins with removing both the rear Exhaust Manifold pipe along with the transaxle assembly. Clever the left Exhaust Manifold off its position on the front Exhaust Manifold pipe through two bolts before disconnecting the single bolt uniting the front Exhaust Manifold pipe to the crankcase. First unfasten the coil cassette ground wire nut on the Cylinder Head and afterward remove the bolt which holds the front Exhaust Manifold pipe to the Cylinder Head. A replacement for the egr valve inlet pipe becomes necessary whenever it separates from the water crossover since its crush seal connection cannot be reused. The egr inlet pipe must be detached from the front Exhaust Manifold pipe while you remove both components from the left Exhaust Manifold along with the original front Exhaust Manifold pipe seal. The operation requires removal of both the Exhaust Manifold flange retainer along with the front Exhaust Manifold pipe. Start by positioning the retainer device together with a new front Exhaust Manifold pipe seal against the left Exhaust Manifold before securing the front Exhaust Manifold pipe through it. Use bolts (1, 3) to attach the front Exhaust Manifold pipe to its engine position while torquing the mounting bolts to 25 nm (18 ft. Lbs.). Last, hand-start the inlet pipe nut of the front Exhaust Manifold to avoid cross threading before tightening it to 60 nm (44 ft. Lbs.). Place the transaxle assembly together with the rear Exhaust Manifold pipe before final installation. When attaching the egr inlet pipe nut to the front Exhaust Manifold pipe start it by hand to prevent cross-threading and tighten it to 60 nm (44 ft. Lbs.). Finally, reinstall the transaxle assembly and the rear Exhaust Manifold pipe.

OEM Cadillac Seville Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

43 Exhaust Pipes found

View related parts
Cadillac Seville Muffler & Pipe Part Number: 88959326
Product Specifications
- Other Name: Muffler Assembly, Exhaust (W/Exhaust & Tail Pipe & 3Way Catalytic Converter; Exhaust Pipe; Muffler, Exhaust; Muffler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler Part Number: 1628406
Product Specifications
- Other Name: Muffler, Exhaust
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Exhaust Pipe Part Number: 12554636
Product Specifications
- Other Name: Pipe, Catalytic Converter; Crossover Pipe; Front Pipe; Pipe, Exhaust Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Cadillac Seville | Base | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Intermediate Pipe Part Number: 3522726
Product Specifications
- Other Name: Pipe Assembly; Exhaust Pipe; Intermed Pipe; Pipe, Exhaust Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Intermediate Pipe Part Number: 1638595
Product Specifications
- Other Name: Pipe Assembly, Intermediate; Exhaust Pipe; Intermed Pipe; Pipe, Exhaust Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Intermediate Pipe Part Number: 3522855
Product Specifications
- Other Name: Pipe Assembly- Exhaust; Exhaust Pipe; Intermed Pipe; Evaporator Core Cover; Pipe, Exhaust Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Exhaust Pipe, Rear Part Number: 3544526
Product Specifications
- Other Name: Pipe Assembly-Exhaust Manifold Rear; Front Pipe; Pipe, Exhaust Pipe
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Resonator Part Number: 1622802
Product Specifications
- Other Name: Resonater, Exhaust; Resonator, Exhaust
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Exhaust Pipe, Rear Part Number: 3546665
Product Specifications
- Other Name: Pipe Assembly-Exhaust Manifold Rear; Front Pipe; Pipe, Exhaust Pipe
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1995 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler & Pipe, Driver Side Part Number: 3527049
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/Exhaust Pipe & Tail Pipe); Muffler; Muffler, Exhaust; Exhaust Pipe
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Cadillac Seville | Base | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Muffler & Pipe Part Number: 3522852
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/Tail Pipe); Exhaust Pipe; Muffler; Muffler, Exhaust
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Muffler & Pipe Part Number: 25632778
Product Specifications
- Other Name: Muffler, Exhaust; Exhaust Pipe; Muffler
- Replaced by: 25644674
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler, Driver Side Part Number: 25644674
Product Specifications
- Other Name: Muffler Assembly-Exhaust W/Tail Pipe Left-Hand; Muffler, Exhaust Tail Pipe; Muffler, Exhaust
- Position: Driver Side
- Replaces: 25632778, 25641774
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler, Driver Side Part Number: 25663806
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/Tail Pipe) Left-Hand; Muffler, Exhaust Tail Pipe; Muffler, Exhaust
- Position: Driver Side
- Replaces: 25650061
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler & Pipe, Passenger Side Part Number: 3531055
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/Tail Pipe); Exhaust Pipe; Muffler; Muffler, Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Cadillac Seville | Base | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Rear Muffler, Driver Side Part Number: 3529188
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/Exhaust Pipe & Tail Pipe); Muffler & Pipe; Muffler; Muffler, Exhaust; Exhaust Pipe
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1995 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler, Passenger Side Part Number: 25640095
Product Specifications
- Other Name: Muffler, Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Intermed Pipe Part Number: 3537025
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/ Exhaust Pipe & Tail Pipe); Muffler; Muffler, Exhaust
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1995 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Muffler & Pipe, Driver Side Part Number: 3522853
Product Specifications
- Other Name: Muffler Assembly- Exhaust (W/Tail Pipe); Exhaust Pipe; Case; Muffler; Muffler, Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Muffler & Pipe, Passenger Side Part Number: 25663812
Product Specifications
- Other Name: Muffler Assembly-Exhaust (W/Resonator, Exhaust & Tail Pipe) Right-Hand; Exhaust Pipe; Muffler, Exhaust Tail Pipe; Muffler, Exhaust; Muffler
- Position: Passenger Side
- Replaces: 25642877
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS

| Page 1 of 3 |Next >

1-20 of 43 Results

Cadillac Seville Exhaust Pipe

Want to cut long-term maintenance and repair costs? Choose OEM Exhaust Pipe. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Seville parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Seville Exhaust Pipe includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Exhaust Pipe is one of the component, which can exclusively reflect Cadillac's priority to the reliability and performance. Located in the Cadillac Seville engine, the Exhaust Pipe is specifically engineered to quickly release poisonous gases such as carbon monoxide from the engine and prevent them from entering the passenger compartment therefore increasing passenger safety. Designed for distinct Seville automobiles manufactured from 1975 to 2004, this exhaust pipe is an essential component that influences the automobile's efficiency. Tend to be located on the side of the vehicle opposite the kerb, facilitating proper expulsion of the fuel while avoiding cut and corrosion. The Exhaust Pipe is designed to fit perfectly with other parts in the exhaust system like the Cadillac Seville Muffler, and Cadillac Seville Catalytic Converter, to facilitate exhaust flow. Interestingly, the outlet of the exhaust pipe may differ with the models of Seville where some may contain more than one pipe for high performance. This also plays a part in making the vehicle strong while at the same time showing how Cadillac has an innovative outlook towards luxury automobile manufacturing. Better fuel efficiency and minimum emission Casements are other distinguishing attributes of Exhaust Pipe; further solidifying Cadillac's reputation as a pioneer. Thus, above all, the Exhaust Pipe is not merely an auditory component; it is a manifestation of the Cadillac's soul, an emblem of Cadillac's fidelity to creating vehicles that are safe and efficient, and that epitomize the luxury of sports cars.

Cadillac Seville Exhaust Pipe Parts and Q&A

Exhaust Pipe
12564240
Q: How to service and repair the exhaust crossover exhaust pipe on Cadillac Seville?
A:
The first step for servicing the exhaust crossover pipe requires removal of the transaxle assembly. The service begins with removing the two bolts which secure the left side Exhaust Manifold. Replacment of the egr valve inlet pipe is necessary after disconnecting it because the water crossover uses a crush seal connection. Remove both the egr inlet pipe from the exhaust crossover before taking off the exhaust front pipe. The service procedure begins by unfastening the bolt connecting the crossover pipe to the crankcase then the nut securing the ignition module ground wire to the Cylinder Head and finishing with the bolt holding the crossover pipe to the Cylinder Head. Clear the crossover pipe from the engine compartment as the next step. Begin by applying two flange seals to the crossover pipe before positioning it correctly while keeping the lh Exhaust Manifold joint free from tightening. Install the exhaust front pipe after supporting it with hand torques to support bolts 1 and 3. Fasten the Cylinder Head support bolt at 25 nm (18 ft. Lbs.) while the crankcase support bolt requires the same torque setting of 25 nm (18 ft. Lbs.). Install the nut which supports the ignition module ground wire on the Cylinder Head before securing it with 17 nm torque value (13 ft. Lbs.). Secure all fasteners by tightening left hand Exhaust Manifold bolts to 25 nm (18 ft. Lbs.). Start the fitting of the egr inlet pipe-to-crossover valve with your hand to avoid threading issues before tightening it to 60 nm (44 ft. Lbs.). Finally, reinstall the transaxle assembly.
Muffler W/Tpipe, Passenger Side
25670396
Q: How to replace the Front Exhaust Pipe on Cadillac Seville?
A:
Safety precautions for hot exhaust systems and removing exhaust parts should be followed before initiatives to replace the front Exhaust Manifold pipe begin. The repair process begins with removing both the rear Exhaust Manifold pipe along with the transaxle assembly. Clever the left Exhaust Manifold off its position on the front Exhaust Manifold pipe through two bolts before disconnecting the single bolt uniting the front Exhaust Manifold pipe to the crankcase. First unfasten the coil cassette ground wire nut on the Cylinder Head and afterward remove the bolt which holds the front Exhaust Manifold pipe to the Cylinder Head. A replacement for the egr valve inlet pipe becomes necessary whenever it separates from the water crossover since its crush seal connection cannot be reused. The egr inlet pipe must be detached from the front Exhaust Manifold pipe while you remove both components from the left Exhaust Manifold along with the original front Exhaust Manifold pipe seal. The operation requires removal of both the Exhaust Manifold flange retainer along with the front Exhaust Manifold pipe. Start by positioning the retainer device together with a new front Exhaust Manifold pipe seal against the left Exhaust Manifold before securing the front Exhaust Manifold pipe through it. Use bolts (1, 3) to attach the front Exhaust Manifold pipe to its engine position while torquing the mounting bolts to 25 nm (18 ft. Lbs.). Last, hand-start the inlet pipe nut of the front Exhaust Manifold to avoid cross threading before tightening it to 60 nm (44 ft. Lbs.). Place the transaxle assembly together with the rear Exhaust Manifold pipe before final installation. When attaching the egr inlet pipe nut to the front Exhaust Manifold pipe start it by hand to prevent cross-threading and tighten it to 60 nm (44 ft. Lbs.). Finally, reinstall the transaxle assembly and the rear Exhaust Manifold pipe.