How to replace the intake manifold on Chevrolet Colorado?

To install the new Intake Manifold, remove Throttle Body, battery box, and oil level indicator/tube. Extract the brake booster hose and the engine wiring harness electrical connector from the manifold absolute pressure (MAP) sensor and engine wiring harness retainer from the Intake Manifold. Also remove the positive crankcase ventilation (PCV) dirty air tube which is found on the camshaft cover and the generator as well. Disconnect the engine wiring harness retainer from the Intake Manifold and remove the upper 2 bolts attaching the engine wiring harness bracket to Intake Manifold. Lift vehicle up to get access other component through the wheelhouse and remove the left front wheel and left front liner of the wheelhouse. Remove the traffective used for removing wiring harness retainers for Battery Cable, engine (4,6) and MAP Sensor after that take off the remaining engine wiring bracket lower bolt and the bracket. Lower the vehicle by removing the bolts of the Intake Manifold, and remove Intake Manifold from the cylinder head by discarding the old seal and mask off the open ports to prevent foreign objects from entering the engine. For installation, clean the sealing surface and install a new seal into the side of the Intake Manifold groove and place the Intake Manifold towards the cylinder head. Lift and raise the vehicle once more to access the Intake Manifold bolts, engine wiring harness bracket bolts, and the wiring harnesses. Torque the Intake Manifold bolts from the inside towards the outside until they reach 10 nm (89 lb in) and secure the engine wiring harness bracket onto the engine with the bolts at 10 nm(89 lb in). Reconnect the engine wiring harness retainers for the Battery Cable, engine (4, 6) and MAP Sensor, re-install the left front wheelhouse liner and left front wheel then reduced the vehicle. Mount the engine wiring harness retainer to the Intake Manifold , install the generator, connect the pcv dirty air tube to the camshaft cover, and then reconnect the engine wiring harness retainer to the Intake Manifold and the electrical connector to the MAP Sensor. Finally, reconnect the brake booster hose, install oil level indicator and tube, battery box, and Throttle Body.

OEM Chevrolet Colorado Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Intake Manifolds found

View related parts
Chevrolet Colorado Intake Manifold Part Number: 89017742
$356.61 MSRP: $607.12
You Save: $250.51 (42%)
ADD TO CART
Product Specifications
- Other Name: Manifold, Intake (Service); Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 5 Cyl 3.5 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12699182
$333.95 MSRP: $573.52
You Save: $239.57 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Intake Plenum; Manifold
- Replaces: 12648915, 12635243
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 Chevrolet Colorado | LT, WT, Z71 | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12620308
$216.35 MSRP: $351.12
You Save: $134.77 (39%)
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Manifold
- Replaces: 12597598
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chevrolet Colorado | LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12698870
$47.51 MSRP: $74.41
You Save: $26.90 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Replaces: 12694867
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Colorado | LT, Trail Boss, WT, Z71, ZR2 | 4 Cyl 2.7 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12675740
$219.07 MSRP: $372.92
You Save: $153.85 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2022 Chevrolet Colorado | LT, WT, Z71, ZR2 | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12638038
$224.44 MSRP: $382.10
You Save: $157.66 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2012 Chevrolet Colorado | LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12631023
$269.56 MSRP: $444.06
You Save: $174.50 (40%)
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12611155
$348.50 MSRP: $574.12
You Save: $225.62 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Engine Intake Manifold
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 Chevrolet Colorado | LT, WT, Z71 | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 89060572
Product Specifications
- Other Name: Manifold, Intake (Service); Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 Chevrolet Colorado | LS, LT, WT | 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 89060571
Product Specifications
- Other Name: Manifold Assembly, Intake (Service); Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 Chevrolet Colorado | LS, LT, WT | 4 Cyl 2.9 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 89017801
Product Specifications
- Other Name: Manifold Assembly, Intake (Service); Oil Pump; Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS
View related parts
Chevrolet Colorado Intake Manifold Part Number: 12640048
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2022 Chevrolet Colorado | LT, WT, Z71, ZR2 | 4 Cyl 2.8 L DIESEL

Chevrolet Colorado Intake Manifold

Want to cut long-term maintenance and repair costs? Choose OEM Intake Manifold. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Colorado parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Colorado Intake Manifold includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Colorado Intake Manifold helps to dispense the air or even air/fuel mixture to all the cylinders and it directly effects the performance and power of the engine. It functions by drawing in air through either throttle body or carburetor depending with the type of the engine. For example, previous carbureted vehicles draw air-fuel mixture into the manifold, whereas current multiport fuel injected engines incorporate unique injectors in their engines to improve performance. Intake manifolds for Chevrolet Colorado have changed from the years with conventional materials such as cast iron and aluminum to light weight plastic composites for better fuel combustions and cooling. Some models have fully variable intake manifold (FVIM) or variable-length intake manifold (VLIM) which helps to control the air and pressure intake according to the load of the engine to increase torque and power. Altogether, the design and the choice of material in the Chevrolet Colorado intake manifold lead to the improved engine performance and efficiency.

Chevrolet Colorado Intake Manifold Parts and Q&A

Intake Manifold
12620308
Q: How to replace the intake manifold on Chevrolet Colorado?
A:
To install the new Intake Manifold, remove Throttle Body, battery box, and oil level indicator/tube. Extract the brake booster hose and the engine wiring harness electrical connector from the manifold absolute pressure (MAP) sensor and engine wiring harness retainer from the Intake Manifold. Also remove the positive crankcase ventilation (PCV) dirty air tube which is found on the camshaft cover and the generator as well. Disconnect the engine wiring harness retainer from the Intake Manifold and remove the upper 2 bolts attaching the engine wiring harness bracket to Intake Manifold. Lift vehicle up to get access other component through the wheelhouse and remove the left front wheel and left front liner of the wheelhouse. Remove the traffective used for removing wiring harness retainers for Battery Cable, engine (4,6) and MAP Sensor after that take off the remaining engine wiring bracket lower bolt and the bracket. Lower the vehicle by removing the bolts of the Intake Manifold, and remove Intake Manifold from the cylinder head by discarding the old seal and mask off the open ports to prevent foreign objects from entering the engine. For installation, clean the sealing surface and install a new seal into the side of the Intake Manifold groove and place the Intake Manifold towards the cylinder head. Lift and raise the vehicle once more to access the Intake Manifold bolts, engine wiring harness bracket bolts, and the wiring harnesses. Torque the Intake Manifold bolts from the inside towards the outside until they reach 10 nm (89 lb in) and secure the engine wiring harness bracket onto the engine with the bolts at 10 nm(89 lb in). Reconnect the engine wiring harness retainers for the Battery Cable, engine (4, 6) and MAP Sensor, re-install the left front wheelhouse liner and left front wheel then reduced the vehicle. Mount the engine wiring harness retainer to the Intake Manifold , install the generator, connect the pcv dirty air tube to the camshaft cover, and then reconnect the engine wiring harness retainer to the Intake Manifold and the electrical connector to the MAP Sensor. Finally, reconnect the brake booster hose, install oil level indicator and tube, battery box, and Throttle Body.