How to replace the Brake Proportioning Valve on Chevrolet Monte Carlo?

To remove the proportioning valve instead, first, do not clean the part in any cleaning preparation since its components are pre-lubricated with a special grease. First, doff the bracket from the master cylinder, master cylinder reservoir next. Then remove the proportioning valve caps, O-rings, and springs, after which remove the proportioning valve pistons with the use of needle nose pliers not to damage the piston stems. Replace the piston seals (proportioning valve seals) from the pistons and look for corrosion and deformation of the pistons, replacing them as required. Treat all the parts with clean denatured alcohol and dry then with a non-lubricated compressed air. During installation, lubricate the O-rings and the proportioning valve seals, and piston stems with the silicone grease that is included in the repair kit. Set new seals to the proportioning valve pistons with the lips facing up towards the cap and re-install pistons and seals into the master cylinder body. Mount the springs and new O-rings into the grooves of the proportioning valve caps, then tighten caps to 27 Nm (20 ft. lbs). Finally, reattach the bracket and the master cylinder reservoir, and then proceed with bleeding of the brakes.

OEM Chevrolet Monte Carlo Brake Proportioning Valve

Proportioning Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Proportioning Valves found

View related parts
Chevrolet Monte Carlo Pressure Metering Valve
Part Number: 18014469
$13.11 MSRP: $16.23
You Save: $3.12 (20%)
ADD TO CART
Product Specifications
- Other Name: Brake Proportioning Valve; Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Pressure Metering Valve
Part Number: 25509419
Product Specifications
- Other Name: Valve, Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 Chevrolet Monte Carlo | Base, LS, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Chevrolet Monte Carlo Modulator Valve
Part Number: 15903776
Product Specifications
- Other Name: Valve, Electronic Brake Control; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Pressure Metering Valve
Part Number: 10289556
Product Specifications
- Other Name: Valve Assembly-Brake Proportioning; Brake Proportioning Valve; Valve, Brake Master Cylinder Proportioning
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Chevrolet Monte Carlo | LS, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

Chevrolet Monte Carlo Brake Proportioning Valve

Our website offers an extensive catalog of genuine Chevrolet Monte Carlo Brake Proportioning Valve at unbeatable prices. Every OEM Chevrolet Monte Carlo Brake Proportioning Valve comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Monte Carlo Brake Proportioning Valve Parts Questions & Experts Answers

Pressure Metering Valve
18014469
Q: How to replace the Brake Proportioning Valve on Chevrolet Monte Carlo?
A: To remove the proportioning valve instead, first, do not clean the part in any cleaning preparation since its components are pre-lubricated with a special grease. First, doff the bracket from the master cylinder, master cylinder reservoir next. Then remove the proportioning valve caps, O-rings, and springs, after which remove the proportioning valve pistons with the use of needle nose pliers not to damage the piston stems. Replace the piston seals (proportioning valve seals) from the pistons and look for corrosion and deformation of the pistons, replacing them as required. Treat all the parts with clean denatured alcohol and dry then with a non-lubricated compressed air. During installation, lubricate the O-rings and the proportioning valve seals, and piston stems with the silicone grease that is included in the repair kit. Set new seals to the proportioning valve pistons with the lips facing up towards the cap and re-install pistons and seals into the master cylinder body. Mount the springs and new O-rings into the grooves of the proportioning valve caps, then tighten caps to 27 Nm (20 ft. lbs). Finally, reattach the bracket and the master cylinder reservoir, and then proceed with bleeding of the brakes.