How to replace the front brake line on Chevrolet Monte Carlo?

Raise the car with supports and dismantle its front wheel setup to access the front brake hose. After cleaning dirt from both brake hoses and brake pipe fitting parts set a rubber cap or plug on the brake pipe fitting end to shield fluid contents. Hold the brake pipe with the second wrench to disconnect the brake hose without distorting the structure or support bracket. Unclip the brake hose bracket holder and connect the hose pieces. Also remove the brake hose caliper bolt from the assembly and take out the brake hose. Take away the two copper gaskets on the brake hose that may be bonded to the caliper and pipe ends. Install new copper brake hose gaskets onto brake hose and connect this assembly to the brake hose bolt using appropriate tools. Fasten the brake hose to caliper bolt into its designated location on the brake caliper while applying a torque of 54 nm (40 ft lbs). Place the brake hose into the bracket while keeping the vehicle weight on the suspension. Place the hose fitting in the bracket notch without bends for proper setup. Put the retainer on top of the hose fitting at the bracket and pull off any rubber cover from the brake pipe end. Use a back up wrench to fit the brake pipe end to brake hose before tightening it to 18 nm (13 ft. Lbs.). Place the wheel set in front and park the car with safety steps to prevent the hose from hitting suspension components. Our team will disconnect the hose when it meets any surface unit. Close the hydraulic brake system by following the bleeding procedure and set the car down to the ground.

How to replace the rear brake line on Chevrolet Monte Carlo?

To switch brake hoses at the rear start by lifting the vehicle and placing support stands then detach the back tire along with its wheel. Clean the brake hose and brake pipe fitting connections from all soil particles while placing a rubber seal on the exposed brake pipe end to protect the fluid. Put on a back up wrench to detach the brake pipe fitting from its location at the brake hose without bending either brake component. Loosen the clip on the bracket first and take off the brake hose from its bracket connections. Take off the brake hose to caliper bolt from the brake caliper and disconnect the brake hose only to discard the two copper brake hose gaskets that stuck to the caliper or hose end. Replace two new copper brake hose gaskets when fitting the brake hose bolt to the caliper. Also connect new brake hose to the caliper and bolt it down with 54 nm pressure. Use the suspension load to put the brake hose into the bracket without bends. Align the hose fitting with the bracket notch before securing. Place the retainer over the hose fitting at the bracket before you attach the brake hose to the brake pipe port. Tighten the joint with a back up wrench to 15 nm (11ft. Lbs.) while preventing bends to bracket or pipe. Set the rear tire and wheel unit back in place but beware that the hose should not touch suspension parts during installation. Fix this if the hose makes contact. Complete the brake work by draining the hydraulic system then putting the vehicle down.

OEM Chevrolet Monte Carlo Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Brake Lines found

View related parts
Chevrolet Monte Carlo Flex Hose Part Number: 9762810
$12.42 MSRP: $22.19
You Save: $9.77 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Hose & Sleeve Assembly; Hydraulic Hose; Brake Hose; Brake Line
- Replaced by: 19169839
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, LS, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Chevrolet Monte Carlo Brake Hose, Front Part Number: 19169839
$12.42 MSRP: $22.19
You Save: $9.77 (45%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Line; Hose; Hose, Hydraulic Brake
- Position: Front
- Replaces: 09762810, 18031820, 9762810
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, LS, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Chevrolet Monte Carlo Flex Hose, Passenger Side Part Number: 10112054
$22.84 MSRP: $42.90
You Save: $20.06 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Front Driver Side Part Number: 22163577
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose Part Number: 9761251
Product Specifications
- Other Name: Hose Assembly-Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, LS, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Chevrolet Monte Carlo Flex Hose, Front Passenger Side Part Number: 84393884
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 15242631
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Passenger Side Part Number: 22163462
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 22163458
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Driver Side Part Number: 22163461
Product Specifications
- Other Name: Brake Hose; Hydraulic Hose; Brake Line; Hose, Hydraulic Brake
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Front Part Number: 22163414
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Rear Driver Side Part Number: 19366667
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 15242630
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Driver Side Part Number: 15876864
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaces: 22163799
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Passenger Side Part Number: 15876863
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 22163798
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Driver Side Part Number: 10112053
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Front Driver Side Part Number: 84393885
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 15242632
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose Part Number: 22163367
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaces: 17999600
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Flex Hose, Passenger Side Part Number: 15242629
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS

Chevrolet Monte Carlo Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Monte Carlo parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Monte Carlo Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Monte Carlo Brake Line is an important part which translates brake fluid from the master cylinder to the brake caliper pistons to make the hydraulic braking work. Steel brake line is vulnerable to corrosion and mechanical shocks to the extent that fluid leakages and loss of pressure might result. It also affects its brake through both its physical and internal like brake hoses, which can be damaged. On occasions where replacement is necessary, pre bent brake line kits and many other corrosion resistant Stainless Steel hoses are used in Quick Fitments. Switching to the braided stainless steel hoses can give a more tactful brake pedal, which would come in handy for the spirited driving.

Chevrolet Monte Carlo Brake Line Parts and Q&A

Flex Hose, Front Passenger Side
84393884
Q: How to replace the front brake line on Chevrolet Monte Carlo?
A:
Raise the car with supports and dismantle its front wheel setup to access the front brake hose. After cleaning dirt from both brake hoses and brake pipe fitting parts set a rubber cap or plug on the brake pipe fitting end to shield fluid contents. Hold the brake pipe with the second wrench to disconnect the brake hose without distorting the structure or support bracket. Unclip the brake hose bracket holder and connect the hose pieces. Also remove the brake hose caliper bolt from the assembly and take out the brake hose. Take away the two copper gaskets on the brake hose that may be bonded to the caliper and pipe ends. Install new copper brake hose gaskets onto brake hose and connect this assembly to the brake hose bolt using appropriate tools. Fasten the brake hose to caliper bolt into its designated location on the brake caliper while applying a torque of 54 nm (40 ft lbs). Place the brake hose into the bracket while keeping the vehicle weight on the suspension. Place the hose fitting in the bracket notch without bends for proper setup. Put the retainer on top of the hose fitting at the bracket and pull off any rubber cover from the brake pipe end. Use a back up wrench to fit the brake pipe end to brake hose before tightening it to 18 nm (13 ft. Lbs.). Place the wheel set in front and park the car with safety steps to prevent the hose from hitting suspension components. Our team will disconnect the hose when it meets any surface unit. Close the hydraulic brake system by following the bleeding procedure and set the car down to the ground.
Flex Hose, Passenger Side
15876863
Q: How to replace the rear brake line on Chevrolet Monte Carlo?
A:
To switch brake hoses at the rear start by lifting the vehicle and placing support stands then detach the back tire along with its wheel. Clean the brake hose and brake pipe fitting connections from all soil particles while placing a rubber seal on the exposed brake pipe end to protect the fluid. Put on a back up wrench to detach the brake pipe fitting from its location at the brake hose without bending either brake component. Loosen the clip on the bracket first and take off the brake hose from its bracket connections. Take off the brake hose to caliper bolt from the brake caliper and disconnect the brake hose only to discard the two copper brake hose gaskets that stuck to the caliper or hose end. Replace two new copper brake hose gaskets when fitting the brake hose bolt to the caliper. Also connect new brake hose to the caliper and bolt it down with 54 nm pressure. Use the suspension load to put the brake hose into the bracket without bends. Align the hose fitting with the bracket notch before securing. Place the retainer over the hose fitting at the bracket before you attach the brake hose to the brake pipe port. Tighten the joint with a back up wrench to 15 nm (11ft. Lbs.) while preventing bends to bracket or pipe. Set the rear tire and wheel unit back in place but beware that the hose should not touch suspension parts during installation. Fix this if the hose makes contact. Complete the brake work by draining the hydraulic system then putting the vehicle down.