How to replace the brake master cylinder on Chevrolet Monte Carlo?

The Brake Fluid Level Sensor and pipes must detach from the master cylinder before brake service. Keep brake pipeline ends protected during this procedure. You should open brake pipe ends and pin them before unbolting the master cylinder's mounting nuts and removing it from the vehicle to drain all fluid from the reservoir. Before adding the master cylinder to the vacuum Brake Booster you must bleed all fluid from it. Then install and tighten the mounting nuts to 25 nm (18 ft. Lbs.). Connect the plugged brake pipes to the master cylinder and tighten fittings to 15 nm (11 ft. Lbs.). Rejoin the Brake Fluid Level Sensor electrical connector before bleeding the braking system.

How to overhaul the brake master cylinder on Chevrolet Monte Carlo?

First disconnect the Brake Master Cylinder then mount its flange in a vise while keeping the primary Piston accessible in the back. Before removing the cap and diaphragm you need to clean the reservoir area around the cap. Check the cap and diaphragm for cuts, cracks, nicks, or mischief and replace them if necessary. Use a smooth instrument to push the primary Piston down until you disconnect the Piston retainer and primary Piston system from the cylinder base. Securing the cylinder ports blocks both inlets and outflows. Supply low pressure non-lubricated filtered air into the front outlet port to extract the secondary Piston together with the primary and secondary seals and return spring. Throw away the major Piston pieces plus the support plate from the second Piston. Use denatured alcohol to clean all parts of the master cylinder assembly plus secondary Piston and return spring while preventing abrasive particles from entering. Check the master cylinder for damage throughout including its bore, inlet and outlet ports, Piston, and the spring system before replacing the unit if you find problems. Use filtered non-lubricated air to dry all components after you apply delco supreme 11(R) brake fluid from a sealed container through the master cylinder bore, secondary Piston bore, return spring, and all parts for assembly. Put the secondary Piston primary seal parts and new secondary seal onto it before placing the return spring along with this assembly into the cylinder bore. Finally place the new primary Piston assembly. Apply the flat end of a tool to push down the primary Piston before adding the new Piston retainer. Then reinstall the master cylinder reservoir with its diaphragm and cap before returning the master cylinder to its place.

OEM Chevrolet Monte Carlo Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Brake Master Cylinders found

View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 18021217
$113.55 MSRP: $211.90
You Save: $98.35 (47%)
ADD TO CART
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 18029965
$95.95 MSRP: $265.88
You Save: $169.93 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 18022002
Product Specifications
- Other Name: Cylinder Kit, Brake Master; Overhaul Kit; Master Cylinder Repair Kit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2007, 2000-2002 Chevrolet Monte Carlo | LS, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Overhaul Kit Part Number: 18010083
Product Specifications
- Other Name: Cylinder Kit, Brake Master; Master Cylinder Repair Kit; Cylinder Kit, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, LS, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 19209261
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Replaces: 18060783
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Chevrolet Monte Carlo | LS, LT, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 19209260
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Replaces: 18060780, 18026277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 19209247
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Replaces: 18047667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, SS, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 19209185
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Replaces: 10382902
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 18060781
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Chevrolet Monte Carlo | LS, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 18013429
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, LS, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Chevrolet Monte Carlo Master Cylinder Part Number: 15925739
Product Specifications
- Other Name: Cylinder, Brake Master Cylinder; Brake Master Cylinder
- Replaces: 10337908
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS

Chevrolet Monte Carlo Brake Master Cylinder

Want to cut long-term maintenance and repair costs? Choose OEM Brake Master Cylinder. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Monte Carlo parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Monte Carlo Brake Master Cylinder includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Brake Master Cylinder as applied and used in Chevrolet Monte Carlo cars is a very essential part of this automobile's braking system which is made to translate pressure exerted on the brake pedal by the driver into hydraulic pressure. This hydraulic pressure is extended to the slave cylinders and in return it operates the brakes by developing the right friction that is need to bring the vehicle to a standstill. The master cylinder may contain multiple pistons, seals and springs all located within either cast iron or aluminum construction material, the fluid reservoir unless built into the master cylinder unit may be located separately. Year after year Chevrolet Monte Carlo models have incorporated the use of dual circuit master cylinders and the worst that can happen is that one of the two circuits could fail while the other has enough braking peddle. This design increases safety in that the unit can still function even if there is failure in the hydraulic system. Some of the known complaints of the Brake Master Cylinder are fluid leakages and internal failures, these result in the fading of brakes.

Chevrolet Monte Carlo Brake Master Cylinder Parts and Q&A

Master Cylinder
18022002
Q: How to replace the brake master cylinder on Chevrolet Monte Carlo?
A:
The Brake Fluid Level Sensor and pipes must detach from the master cylinder before brake service. Keep brake pipeline ends protected during this procedure. You should open brake pipe ends and pin them before unbolting the master cylinder's mounting nuts and removing it from the vehicle to drain all fluid from the reservoir. Before adding the master cylinder to the vacuum Brake Booster you must bleed all fluid from it. Then install and tighten the mounting nuts to 25 nm (18 ft. Lbs.). Connect the plugged brake pipes to the master cylinder and tighten fittings to 15 nm (11 ft. Lbs.). Rejoin the Brake Fluid Level Sensor electrical connector before bleeding the braking system.
Master Cylinder
19209185
Q: How to overhaul the brake master cylinder on Chevrolet Monte Carlo?
A:
First disconnect the Brake Master Cylinder then mount its flange in a vise while keeping the primary Piston accessible in the back. Before removing the cap and diaphragm you need to clean the reservoir area around the cap. Check the cap and diaphragm for cuts, cracks, nicks, or mischief and replace them if necessary. Use a smooth instrument to push the primary Piston down until you disconnect the Piston retainer and primary Piston system from the cylinder base. Securing the cylinder ports blocks both inlets and outflows. Supply low pressure non-lubricated filtered air into the front outlet port to extract the secondary Piston together with the primary and secondary seals and return spring. Throw away the major Piston pieces plus the support plate from the second Piston. Use denatured alcohol to clean all parts of the master cylinder assembly plus secondary Piston and return spring while preventing abrasive particles from entering. Check the master cylinder for damage throughout including its bore, inlet and outlet ports, Piston, and the spring system before replacing the unit if you find problems. Use filtered non-lubricated air to dry all components after you apply delco supreme 11(R) brake fluid from a sealed container through the master cylinder bore, secondary Piston bore, return spring, and all parts for assembly. Put the secondary Piston primary seal parts and new secondary seal onto it before placing the return spring along with this assembly into the cylinder bore. Finally place the new primary Piston assembly. Apply the flat end of a tool to push down the primary Piston before adding the new Piston retainer. Then reinstall the master cylinder reservoir with its diaphragm and cap before returning the master cylinder to its place.