How to replace the right rear exhaust manifold on Chevrolet Monte Carlo?

First step to replace the right rear Exhaust Manifold requires removal of the fuel injector sight shield followed by the cross vehicle brace and exhaust crossover pipe from the right Exhaust Manifold. First detach the egr adapter pipe and the air pipe only when present on the vehicle. Begin by lifting the vehicle and then disconnect the catalytic converter pipe from the right Exhaust Manifold followed by lowering the vehicle. The heated Oxygen Sensor pigtail lead must be removed from the generator bracket brace before disconnecting the right Spark Plug Wires. Begin by uninstalling the right engine lift bracket bolt along with the nut and proceed with removing the right engine lift bracket. The first step requires removal of the fuel injector sight shield bracket nuts before proceeding to uninstall the bracket followed by extracting the transaxle fluid filler tube. Start by unfastening the bolts and nuts securing the right Exhaust Manifold and gasket where they can be detached along with the upper and lower right Exhaust Manifold heat shields. The heated Oxygen Sensor needs removal from the manifold before proceeding with a manifold replacement. Installation should start by placing the heated Oxygen Sensor onto the new manifold before putting on both lower and upper right Exhaust Manifold heat shields. The egr pipe outlet should be checked for leaks while the egr adapter must be replaced if needed. Begin by placing an entirely new right Exhaust Manifold Gasket before installing the right Exhaust Manifold and tighten its bolts and nuts to 30 nm (22 ft. Lbs.). Install the transaxle fluid filler tube while attaching the fuel injector sight shield bracket with its nuts set at 30 nm (22 ft. Lbs.). The right engine lift bracket requires reinstallation along with fastening the bolt and nut at 30 nm (22 ft. Lbs.). Place the right Spark Plug Wires back in position and put the wiring harness and heater hose retaining clips onto the fuel injector sight shield bracket. After that, raise the vehicle for support. Connect the catalytic converter pipe to the right Exhaust Manifold before lowering the vehicle and install the air pipe if installed. The egr adapter pipe goes onto the right Exhaust Manifold before installing the exhaust crossover pipe and the fuel injector sight shield.

OEM Chevrolet Monte Carlo Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Exhaust Manifolds found

View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 12568405
$204.26 MSRP: $303.21
You Save: $98.95 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 12615497
$459.48 MSRP: $660.74
You Save: $201.26 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 12569054
$189.01 MSRP: $297.41
You Save: $108.40 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | SS | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 12569053
$202.41 MSRP: $318.47
You Save: $116.06 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | SS | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 12603753
$218.06 MSRP: $340.05
You Save: $121.99 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 12588004
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Chevrolet Monte Carlo | LT, SS | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 14014500
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, LS, SS | 8 Cyl 5.0 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 22530287
Product Specifications
- Other Name: Manifold, Exhaust; Manifold; Manifold, Engine Exhaust Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986 Chevrolet Monte Carlo | Base, LS, SS | 8 Cyl 5.0 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 411961
Product Specifications
- Other Name: Manifold, Exhaust; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Monte Carlo | Base | 8 Cyl 5.7 L DIESEL
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 24507481
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet Monte Carlo | SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 24504379
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2005 Chevrolet Monte Carlo | LS, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car, Z34 | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 24503918
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2003 Chevrolet Monte Carlo | LS, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car, Z34 | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 24505129
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 10162002
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 24507155
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Driver Side Part Number: 24505127
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 25507804
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Monte Carlo | Base | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 24507154
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 12576864
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Monte Carlo | LT, SS | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Exhaust Manifold, Passenger Side Part Number: 10244605
Product Specifications
- Other Name: Manifold, Engine Exhaust Manifold; Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Monte Carlo | LS | 6 Cyl 3.1 L GAS

| Page 1 of 2 |Next >

1-20 of 25 Results

Chevrolet Monte Carlo Exhaust Manifold

Want to cut long-term maintenance and repair costs? Choose OEM Exhaust Manifold. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Monte Carlo parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Monte Carlo Exhaust Manifold includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Exhaust Manifold of Chevrolet Monte Carlo vehicles is used in channeling the hot exhaust gases from the engine to the exhaust system in order to maintain good engine performance as well as minimize emission of unhealthy gases. Located at different positions depending on the engine configuration, the manifold plays a role of ensuring that the exhaust gases pass through other parts such as the converter and the muffler, besides preventing the back flow of the intake gases, a factor that may reduce on the efficiency of the engine. Chevrolet Monte Carlo models have also come with various styles of Exhaust Manifold; these include the cast iron and the stainless steel ones, together with the high performance headers which help to reduce the flow restriction in the exhaust. Headers are the most efficient in enhancing the exhaust gas velocity hence enhancing the overall performance of the engine. Different designs and materials used in these exhaust manifolds are the cause of varying durability and efficiency of the manifolds hence the need to replace any that fail as soon as possible to avoid compromising the health and safety of the vehicle.

Chevrolet Monte Carlo Exhaust Manifold Parts Questions & Experts Answers

Exhaust Manifold, Passenger Side
24503918
Q: How to replace the right rear exhaust manifold on Chevrolet Monte Carlo?
A:
First step to replace the right rear Exhaust Manifold requires removal of the fuel injector sight shield followed by the cross vehicle brace and exhaust crossover pipe from the right Exhaust Manifold. First detach the egr adapter pipe and the air pipe only when present on the vehicle. Begin by lifting the vehicle and then disconnect the catalytic converter pipe from the right Exhaust Manifold followed by lowering the vehicle. The heated Oxygen Sensor pigtail lead must be removed from the generator bracket brace before disconnecting the right Spark Plug Wires. Begin by uninstalling the right engine lift bracket bolt along with the nut and proceed with removing the right engine lift bracket. The first step requires removal of the fuel injector sight shield bracket nuts before proceeding to uninstall the bracket followed by extracting the transaxle fluid filler tube. Start by unfastening the bolts and nuts securing the right Exhaust Manifold and gasket where they can be detached along with the upper and lower right Exhaust Manifold heat shields. The heated Oxygen Sensor needs removal from the manifold before proceeding with a manifold replacement. Installation should start by placing the heated Oxygen Sensor onto the new manifold before putting on both lower and upper right Exhaust Manifold heat shields. The egr pipe outlet should be checked for leaks while the egr adapter must be replaced if needed. Begin by placing an entirely new right Exhaust Manifold Gasket before installing the right Exhaust Manifold and tighten its bolts and nuts to 30 nm (22 ft. Lbs.). Install the transaxle fluid filler tube while attaching the fuel injector sight shield bracket with its nuts set at 30 nm (22 ft. Lbs.). The right engine lift bracket requires reinstallation along with fastening the bolt and nut at 30 nm (22 ft. Lbs.). Place the right Spark Plug Wires back in position and put the wiring harness and heater hose retaining clips onto the fuel injector sight shield bracket. After that, raise the vehicle for support. Connect the catalytic converter pipe to the right Exhaust Manifold before lowering the vehicle and install the air pipe if installed. The egr adapter pipe goes onto the right Exhaust Manifold before installing the exhaust crossover pipe and the fuel injector sight shield.