How to replace the front drive shaft on Chevrolet Trailblazer?

The replacement of front propeller shaft requires raising the vehicle before removing the steering gear crossmember. Use precise marks to indicate the front axle pinion yoke position with respect to the propeller shaft before removing retainer bolts and retainers from the front axle pinion yoke. The removal method requires special attention because striking the yoke ears or inserting tools between the yoke and Universal Joint may result in injection joint fracturing. To disconnect the propeller shaft from the front axle pinion yoke the bearing caps must be taped up to retain bearing rollers and then the front propeller shaft from the Transfer Case should be removed. To install the propeller shaft insert it into the Transfer Case until both slip yokes snap together. This indicates the full engagement. Precautionary fastener instructions must be followed during the installation of the propeller shaft to the front axle pinion yoke before adding the yoke retainers and bolts and making sure to tighten the front propeller shaft yoke clamp bolts to 20 nm (15 lb ft). Lower the vehicle before you reinstall the steering gear crossmember.

How to replace the rear Drive Shaft on Chevrolet Trailblazer?

Replacement of the rear propeller shaft starts with marking all driveline parts relative to the shaft and axles before separation of components including propeller shafts, drive axles and pinion flanges and output shafts so reinstallation occurs with the same connection points as original assembly according to published specifications and torque values. Begin by raising the vehicle. The reference markings will be established to connect the propeller shaft with both the rear axle pinion yoke and transmission or Transfer Case. Before installing the rear axle pinion yoke retainers and bolts users should avoid damaging the yoke ears while keeping the Universal Joint free from any tools to prevent injection joint fractures. After lifting the vehicle you should slip the propeller shaft ahead to the rear axle pinion yoke separation point before moving the shaft backward to pop off the transmission or Transfer Case attachment. Then remove the complete propeller shaft assembly. The installation process requires an inspection of the Slip Yoke spline area for adequate grease protection. If insufficient grease exists, application of gm p/n 12377985 or an equivalent grease product is mandatory. The propeller shaft needs to be inserted first into the transmission or Transfer Case and its marks from removal should be used for alignment before installing it onto the rear axle pinion yoke where additional reference mark alignment takes place. Mount the yoke retainers along with their bolts while adjusting torque to 20 n.m (15 lb ft). The installation progression concludes with lowering the vehicle.

OEM Chevrolet Trailblazer Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Drive Shafts found

View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 60004994
$523.17 MSRP: $826.88
You Save: $303.71 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15861601
$374.87 MSRP: $746.30
You Save: $371.43 (50%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15163667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 60005879
$607.87 MSRP: $960.76
You Save: $352.89 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaced by: 60009425
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 60004993
$498.91 MSRP: $788.55
You Save: $289.64 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Trailblazer | ACTIV, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15833885
$267.91 MSRP: $662.81
You Save: $394.90 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Trailblazer | LS, LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15833884
$459.54 MSRP: $726.31
You Save: $266.77 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft, Front Part Number: 25833035
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 Chevrolet Trailblazer | Base, LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15036982
Product Specifications
- Other Name: Shaft, Propeller; Driveshaft
- Replaces: 15152332, 15188012
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2009 Chevrolet Trailblazer | Base, LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Axle Assembly, Rear Part Number: 25926158
Product Specifications
- Other Name: Axle Assembly-Rear (4.10 Ratio); Axle Shaft
- Position: Rear
- Replaces: 15842180
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Axle Assembly, Rear Part Number: 15134677
Product Specifications
- Other Name: Axle, Rear Axle; Axle Shaft
- Position: Rear
- Replaces: 15065723, 15107453, 15171759
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 25808587
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15233115
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Trailblazer | SS | 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15833883
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Trailblazer | Base, LS, LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15833882
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Trailblazer | LS, LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15833881
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15152336
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2009 Chevrolet Trailblazer | Base, LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15833880
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15113111
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 Chevrolet Trailblazer | LS, LT, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Drive Shaft Part Number: 15194472
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Trailblazer | Base, LS, LT | 8 Cyl 5.3 L GAS

Chevrolet Trailblazer Drive Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Drive Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Trailblazer parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Trailblazer Drive Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Trailblazer Drive Shaft is a functional part of the automobile, which transfers mechanical power and torque from the engine or transmission to the drive wheels efficiently. This metal rod is intended for torsion and shear stress carrying capacity, and possesses minimum inertial characteristics. Chevrolet Trailblazer makes use of different sorts of Drive Shafts, one-piece and two-piece shafts are used concerning the need of the vehicle's drivetrain system. Using multiple Drive Shafts, in four-wheel and all-wheel drive layouts of the car, transfer cases in the Chevrolet Trailblazer chute power both front and rear axles. By using universal joint or splined joint, it is possible to achieve variability in the position and space of the joints and these are important aspects of the vehicle. In general, it is clear that the Drive Shaft is an important component without which the vehicle's performance and fuel efficiency cannot be maintained on the level of the Chevrolet Trailblazer.

Chevrolet Trailblazer Drive Shaft Parts and Q&A

Drive Shaft
15036982
Q: How to replace the front drive shaft on Chevrolet Trailblazer?
A:
The replacement of front propeller shaft requires raising the vehicle before removing the steering gear crossmember. Use precise marks to indicate the front axle pinion yoke position with respect to the propeller shaft before removing retainer bolts and retainers from the front axle pinion yoke. The removal method requires special attention because striking the yoke ears or inserting tools between the yoke and Universal Joint may result in injection joint fracturing. To disconnect the propeller shaft from the front axle pinion yoke the bearing caps must be taped up to retain bearing rollers and then the front propeller shaft from the Transfer Case should be removed. To install the propeller shaft insert it into the Transfer Case until both slip yokes snap together. This indicates the full engagement. Precautionary fastener instructions must be followed during the installation of the propeller shaft to the front axle pinion yoke before adding the yoke retainers and bolts and making sure to tighten the front propeller shaft yoke clamp bolts to 20 nm (15 lb ft). Lower the vehicle before you reinstall the steering gear crossmember.
Axle Assembly, Rear
25926158
Q: How to replace the rear Drive Shaft on Chevrolet Trailblazer?
A:
Replacement of the rear propeller shaft starts with marking all driveline parts relative to the shaft and axles before separation of components including propeller shafts, drive axles and pinion flanges and output shafts so reinstallation occurs with the same connection points as original assembly according to published specifications and torque values. Begin by raising the vehicle. The reference markings will be established to connect the propeller shaft with both the rear axle pinion yoke and transmission or Transfer Case. Before installing the rear axle pinion yoke retainers and bolts users should avoid damaging the yoke ears while keeping the Universal Joint free from any tools to prevent injection joint fractures. After lifting the vehicle you should slip the propeller shaft ahead to the rear axle pinion yoke separation point before moving the shaft backward to pop off the transmission or Transfer Case attachment. Then remove the complete propeller shaft assembly. The installation process requires an inspection of the Slip Yoke spline area for adequate grease protection. If insufficient grease exists, application of gm p/n 12377985 or an equivalent grease product is mandatory. The propeller shaft needs to be inserted first into the transmission or Transfer Case and its marks from removal should be used for alignment before installing it onto the rear axle pinion yoke where additional reference mark alignment takes place. Mount the yoke retainers along with their bolts while adjusting torque to 20 n.m (15 lb ft). The installation progression concludes with lowering the vehicle.