How to replace the Auxiliary Blower Motor (without E59) on Chevrolet Uplander?

Replacing the Auxiliary Blower Motor (without E59) requires first removing the inflator air valve opening cover followed by the removal of screws from the hinged cover until the cover from the rear trim panel can be removed. Unclip the tabs before pulling out the trim panel and disconnect all electrical connectors between the auxiliary blower motor and its resistor as well as the auxiliary air temperature actuator. You must first take out the auxiliary blower motor from the blower motor housing by completely removing its mounting screws. The first step for installation requires placing the auxiliary blower motor inside the blower motor housing while following the marked Fastener Notice. You must install the auxiliary blower motor mounting screws according to the torque requirement of 1.6 N.m (14 lb in). Attach the electrical connectors of the auxiliary air temperature actuator followed by the auxiliary blower motor resistor before finishing with the auxiliary blower motor electrical connector. The trim panel requires installation by firmly pushing into the tabs before aligning the cover and securing its screws to achieve a tension of 2.5 N.m (22 lb in). Place the inflator air valve opening cover before completion.

OEM Chevrolet Uplander Blower Motor

A/C Heater Blower Motor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Blower Motors found

View related parts
Chevrolet Uplander Blower Motor Part Number: 15249638
$50.54 MSRP: $149.58
You Save: $99.04 (67%)
ADD TO CART
Product Specifications
- Other Name: Motor Assembly-Blower; Fan & Motor; Motor, A/C Evaporator Blower; Motor, Heater Blower Motor
- Replaces: 10430162, 21998512, 10341223
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Blower Motor Part Number: 15809345
Product Specifications
- Other Name: Motor Assembly-Blower (W/Impeller); HVAC Blower Motor; Blower Assembly; Motor, A/C Evaporator Blower; Motor, Heater Blower Motor
- Replaces: 10341214, 10424943, 10351192, 15103818, 15785328
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS

Chevrolet Uplander Blower Motor

Want to cut long-term maintenance and repair costs? Choose OEM Blower Motor. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Uplander parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Uplander Blower Motor includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Uplander Blower Motor plays the role of the blower to circulate heat or cool air inside a car thus maintaining the interior comfort of car. Often praised for its effectiveness, the Chevrolet Uplander Blower Motor is smooth to control and such enables the drivers to regulate the temperature as preferred. Due to the specific range of Uplander models it fits into, this blower motor will be suitable for use in maintaining the efficiency and safety of the car for its owners if it was manufactured between 2005 and 2009. The Uplander may contain just the single blower motor, thus, improving the air flow within the front and rear compartments of the car. This design not only increases comfort but it also enhances safety of the Chevrolet Uplander; the windshield should always be cleared so that the driver and any other passenger can have proper visibility while driving. It remains evident that blower motor for Chevrolet Uplander has specific characteristics which make it effective and easy to maintain in the context of the automotive market how it can be equally beneficial for avoiding such problems as unresponsiveness of the controls or inconsistencies in the airflow. Thus, prioritizing the functionality of the Blower motor, Chevrolet improves the driving experience for families and weather conditions do not come in the way of safe and comfortable travel. Performance, reliability, and innovative features are defining the Chevrolet Uplander Blower Motor as a crucial part of the minivan and add more credibility to the Uplander's rating as a reliable minivan for families.

Chevrolet Uplander Blower Motor Parts Questions & Experts Answers

Blower Motor
15249638
Q: How to replace the Auxiliary Blower Motor (without E59) on Chevrolet Uplander?
A:
Replacing the Auxiliary Blower Motor (without E59) requires first removing the inflator air valve opening cover followed by the removal of screws from the hinged cover until the cover from the rear trim panel can be removed. Unclip the tabs before pulling out the trim panel and disconnect all electrical connectors between the auxiliary blower motor and its resistor as well as the auxiliary air temperature actuator. You must first take out the auxiliary blower motor from the blower motor housing by completely removing its mounting screws. The first step for installation requires placing the auxiliary blower motor inside the blower motor housing while following the marked Fastener Notice. You must install the auxiliary blower motor mounting screws according to the torque requirement of 1.6 N.m (14 lb in). Attach the electrical connectors of the auxiliary air temperature actuator followed by the auxiliary blower motor resistor before finishing with the auxiliary blower motor electrical connector. The trim panel requires installation by firmly pushing into the tabs before aligning the cover and securing its screws to achieve a tension of 2.5 N.m (22 lb in). Place the inflator air valve opening cover before completion.