Other Name: Actuator, Air Conditioner Vacuum Control; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Actuator, A/C Vacuum Control
Replaces: 89018371, 52498392
Fits the following GMC Models:
Savana 1500 | 2003-2014 | Base, LS, LT, SLE | 6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
Savana 2500 | 2003-2024 | Base, LS, LT, SLE | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Savana 3500 | 2003-2024 | Base, LS, LT, SLE | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Other Name: Actuator, Air Conditioner Control; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; Actuator; Actuator, A/C Vacuum Control
Replaces: 01996840, 1996840
Fits the following GMC Models:
Savana 1500 | 1996-2014 | Base, LS, LT, SLE, SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS
Savana 2500 | 1996-2024 | Base, LS, LT, SLE, SLT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Savana 3500 | 1996-2024 | Base, LS, LT, SLE, SLT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS, 8 Cyl 7.4 L GAS, 8 Cyl 8.1 L GAS
Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; Temperature Door Actuator; Link; Lever; Actuator; Actuator, A/C Control
Fits the following GMC Models:
Acadia | 2017-2023 | AT4, Denali, SL, SLE, SLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
Q: How to service and repair the defroster Blend Door Actuator on GMC Envoy?
A: In order to service and fix the defroster actuator, start by the elimination of the IP carrier. Next is the removal of screws on the defroster actuator and the electrical connector that is attached to it. After you remove the screws, pull out the defroster actuator. First, for installation, place the new defroster actuator in its place while adhering to the Fastener Notice of the Service Precautions. Fasten the actuator using screws and tighten them to 1.9 N.m (17 lb in). After doing this, reconnect the electrical connector to the defroster actuator and the lastly, reinstall the IP carrier.
Q: How to replace the Blend Door Actuator on GMC Sonoma?
A: To replace the air temperature actuator, you need to disconnect the connector from the will first take off the instrument panel carrier to disconnect the electrical connector. Next, remove the retaining screws for the air temperature actuator and remove the actuator from the hvac module. For installation, place the new air temperature actuator onto the hvac module and make sure it is seated on the locating tab, and then screw it with the retaining screws by screwing it to 1.9 n.m (17 lb ft ). Finally, reconnect the electrical connector and replace instrument panel carrier.
Q: How to replace and initialize the front Blend Door Actuator in the heater/vent module on GMC Jimmy?
A: There is an air temperature actuator on the right-hand side of the heater/vent module on top. Start by removing the instrument panel carrier, disconnecting the electric connector and removing the retaining screws on the air temperature actuator. Remove the actuator from the heater/vent module and install a new actuator making sure that the actuator is seated on the locating tab, insert the retaining screws and fasten it in position to 1.9 n.m (17 lb ft). Restore the electrical connector and install the instrument panel carrier back. To activate the air temperature actuator of vehicles with automatic climate control (C68), the ignition switch should be turned elsewhere to off, then removed the Fuse rdo batt for 10 sec, restore the Fuse and ignite the ignition switch on to make sure the actuator runs in hot and cold phase. Lastly, do a heater output temperature check.