Make sure this part fits

GM 52487607
Actuator

1997-2005 GM

Customer Questions & Expert Answers (22)
GM 52487607 Actuator
  • Part Description
    Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2005 Buick CenturyCustom, Limited, Special Edition6 Cyl 3.1 L GAS
    1999-2004 Buick RegalGS, GSE, LS, LSE6 Cyl 3.8 L GAS
    1997-2004 Chevrolet Corvette50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z068 Cyl 5.7 L GAS
    2000-2003 Chevrolet ImpalaBase, LS, LS Sport6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    2000-2003 Chevrolet Monte CarloLS, LS Competition, LS Sport, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    1998-2002 Oldsmobile IntrigueBase, GL, GLS, GX6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
    1997-2003 Pontiac Grand PrixGT, GTP, SE6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Hi! Is this 52487607 a perfect fit for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 52487607 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the next step after positioning the actuator for the 2005 Buick Century? Posted by Customer
    A:
    Slide the actuator driver onto the shaft until it is fully seated, with the mounting holes flush against the mounting bolts on the HVAC module case.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the next step after securing the actuator for the 2001 Buick Regal? Posted by Customer
    A:
    Reconnect the electrical connector to the actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the next step after seating the actuator for the 2002 Buick Regal? Posted by Customer
    A:
    Install the mounting screws, tightening them to 1.5 N.m (13 lb in), then reconnect the electrical connector to the actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step in the installation process for the 2005 Buick Century? Posted by Customer
    A:
    Attach the defroster actuator to the defroster door arm and snap it into place on the HVAC module.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done with the defroster actuator after operating the recirculation actuator for the 2003 Buick Regal? Posted by Customer
    A:
    Rotate the defroster actuator to the right and up into the opening between the back of the dash and the HVAC module.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you position the defroster valve lever for the 2000 Buick Regal? Posted by Customer
    A:
    Rotate the defroster valve lever fully rearward (counterclockwise).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done with the plunger rod for the 2000 Chevrolet Corvette? Posted by Customer
    A:
    Disconnect the plunger rod from the air inlet valve lever and remove the vacuum actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should you ensure before securing the actuator for the 2004 Chevrolet Corvette? Posted by Customer
    A:
    Ensure the actuator pushrod is not binding on the defrost door lever.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step to replace the left air temperature actuator for the 2002 Chevrolet Corvette? Posted by Customer
    A:
    Begin by removing the front floor kick-up panel and the Bose module.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you secure the defrost door lever during the process for the 2002 Chevrolet Corvette? Posted by Customer
    A:
    Rotate the defrost door lever fully rearward (counterclockwise) and carefully insert a flat bladed tool between the bottom of the lever and the protruding wall of the HVAC module case to keep the lever in place.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you disconnect the inside air temperature sensor aspirator duct for the 2001 Chevrolet Corvette? Posted by Customer
    A:
    Depress the duct retaining tab and twist to release it from the duct muffler.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the final step in the replacement process for the 2000 Chevrolet Impala? Posted by Customer
    A:
    Connect the vacuum lines to the defroster vacuum actuator and reinstall the cross vehicle beam.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the installation process for the new defroster actuator for the 2002 Chevrolet Impala? Posted by Customer
    A:
    Attach the defroster actuator to the defroster door arm and snap it into place on the HVAC module.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be disconnected after removing the IP components for the 2003 Chevrolet Impala? Posted by Customer
    A:
    Disconnect the two vacuum lines from the defroster actuator and the orange vacuum line from the recirculation actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the final step regarding the vacuum lines for the 2001 Chevrolet Monte Carlo? Posted by Customer
    A:
    Remove the hand vacuum pump and reinstall the vacuum line to the recirculation actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the next step after removing the temperature actuator for the 2000 Chevrolet Monte Carlo? Posted by Customer
    A:
    Take out the temperature actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How should the screws be installed for the right air temperature actuator for the 2003 Chevrolet Monte Carlo? Posted by Customer
    A:
    Install the screws, tightening them to 1.5 N.m (13 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should you do after positioning the actuator for the 2002 Chevrolet Monte Carlo? Posted by Customer
    A:
    Slide the actuator onto the shaft until the actuator driver seats completely and the mounting holes are flush with the mounting screws on the HVAC module case.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done after removing the insulator and knee bolster for the 2000 Chevrolet Impala? Posted by Customer
    A:
    Disconnect the electrical connector from the temperature valve electric actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be ensured when sliding the actuator onto the shaft for the 2001 Chevrolet Impala? Posted by Customer
    A:
    Ensure the actuator driver seats completely and the mounting holes are flush with the mounting screws on the HVAC module case.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the next step after removing the actuator for the 2001 Chevrolet Monte Carlo? Posted by Customer
    A:
    Position the new left air temperature actuator, ensuring the slots in the electric actuator driver align with the flats on the shaft and the locating hole aligns with the alignment pin on the HVAC module case.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Actuator 52487607 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 52487607 Actuator is available in the market under the name GM Blend Door Actuator. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 52487607 Actuator fits certain Chevrolet Impala, Corvette, Monte Carlo models, as well as Buick Regal, Century. Additionally, it is compatible with Pontiac Grand Prix and Oldsmobile Intrigue models.
The original GM component designated by manufacturer part number 52487607 maintains top performance when functioning as the Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator unit. The component 52487607 is constructed from durable material and its dimensions span 5.0 x 4.9 x 3.7 inches while weighing 1.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Actuator, A/C Control. The part 52487607 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.