Other Name: Actuator, Air Conditioner Vacuum Control; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Actuator, A/C Vacuum Control
Replaces: 89018371, 52498392
Fits the following Chevrolet Models:
Express 1500 | 2003-2014 | Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
Express 2500 | 2003-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Express 3500 | 2003-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator, A/C Vacuum Control; Actuator, A/C Control
Fits the following Chevrolet Models:
Uplander | 2005-2008 | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
Other Name: Actuator, Air Conditioner Control; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; Actuator; Actuator, A/C Vacuum Control
Replaces: 01996840, 1996840
Fits the following Chevrolet Models:
Express 1500 | 1996-2014 | Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS
Express 2500 | 1996-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Express 3500 | 1996-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS, 8 Cyl 7.4 L GAS, 8 Cyl 8.1 L GAS
P30 | 1996-1999 | Base | 6 Cyl 4.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
Q: How to replace the defroster Blend Door Actuator on Chevrolet Malibu?
A: Secondly, to replace the defroster actuator, take off the IP carrier. Next, detach the blue vacuum hose and the green vacuum hose from the defroster actuator, paying particular attention to where they are located and in which order. After that, hold the actuator lock tab and slide against the actuator. Compress the tabs and pull the actuator linkage off the defroster door. To install, mount the actuator linkage to the defroster door, then slide on the defroster actuator onto the mounting bracket until the tab locks. Reconnect the blue vacuum hose and the green vacuum hose to the defroster actuator, and finally, install the IP carrier.
Q: How to service the Blend Door Actuator in the HVAC module on Chevrolet S10?
A: The first step to service an air temperature actuator entails finding it on the top right side of the hvac module. The initial service requires removing of the instrument panel carrier followed by electrical connector disconnection. Start by unscrewing the retaining screws for the air temperature actuator before you remove it from the hvac module. Attach the air temperature actuator to its position on the hvac module where it should rest on the locating tab. Tighten retaining screws to 1.9 n.m (17 lb ft). Install the instrument panel carrier while reconnecting the electrical connector. The hvac module actuator requires a calibration step as the final procedure.
Q: How to replace the Blend Door Actuator on Chevrolet Tahoe?
A: A temperature actuator can be replaced by removing the instrument panel hush panel. Remove the retaining screws for the temperature actuator, then disconnect the electrical connector from the temperature actuator. After the removal of the actuator, replace with the new temp actuator with the same securing using the retaining screws, but in a tighter manner of 1.6 N.m (14 lb in). Connect the electrical connector back to the temperature actuator and lastly re install the instrument panel hush panel.