Other Name: Module, Air Conditioner Electric Temperature And Motor Control; HVAC Blower Motor Regulator; Blower Motor Resistor; Module; Resistor; A/C Electric Temperature & Motor Control; Air Conditioner (Complete); Heater Blower Motor Regulator
Fits the following Chevrolet Models:
Cruze | 2011-2015 | Diesel, Eco, L, LS, LT, LTZ | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L FLEX, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL
Malibu | 2013-2015 | Eco, LS, LT, LTZ | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L GAS
Malibu Limited | 2016 | LS, LT, LTZ | 4 Cyl 2.5 L GAS
Corvette | 1997-2003 | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS
Impala | 2000-2003 | Base, LS, LS Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
Monte Carlo | 2000-2003 | LS, LS Competition, LS Sport, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
Venture | 1997-2000 | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
Other Name: Resistor, Air Conditioner Electric Temperature And Motor Control; Resistor; Resistor, A/C Electric Temperature And Motor Control; Resistor, Heater Blower Motor
Replaces: 52469502
Fits the following Chevrolet Models:
Express 1500 | 1996-2014 | Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS
Express 2500 | 1996-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
Express 3500 | 1996-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS, 8 Cyl 7.4 L GAS, 8 Cyl 8.1 L GAS
P30 | 1996-1999 | Base | 6 Cyl 4.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
Other Name: Resistor, Air Conditioner Electric Temperature And Motor Control; Blower Motor Resistor; Resistor, A/C Electric Temperature And Motor Control; Resistor, A/C Evaporator Blower
Fits the following Chevrolet Models:
Lumina | 1992-2001 | Base, Euro, LS, LTZ, Z34 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
Monte Carlo | 1995-1999 | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
Q: How to replace the blower motor resistor on Chevrolet Equinox?
A: The first step to replace the Blower Motor Resistor is to disconnect its electrical connector. Unfasten the screws locking the Blower Motor Resistor to the hvac board and lift it free from its position. Place the new Blower Motor Resistor onto the hvac module and fasten it using screws when tightening them to 1 n.m following the fastener notice in service precautions. Secure the electrical plug back to the Blower Motor Resistor last.
Q: How to replace the blower motor resistor assembly on Chevrolet Malibu?
A: Before you can replace the blower motor resistor assembly, first, take off the right side instrument panel insulator. Come next, pull the electrical connector off the blower motor resistor assembly and unscrew the holding screws. After taking out the old resistor assembly, install the new one, but be sure to read the Fastener Notice in Service Precautions. Install the screws and tighten them to 1 N.m (9 lb in), and afterward reconnect the electrical connector. In the end, reinstall the right side instrument panel (IP) insulator.
Q: How to replace the Blower Motor Resistor Assembly (C42) on Chevrolet S10?
A: To replace the Blower Motor Resistor Assembly (C42), this electrical connector should be disconnected first. Then, undo the blower motor resistor mounting screws and pull out the blower motor resistor from the blower case. To install, take the blower motor resistor back into blower case be complied with the Fastener Notice on Service Precautions. Finally, install the blower motor resistor mounting screws and tighten them to 1.9 N.m (17 lb in). Finally, join the electrical connector.