How to replace the blower motor resistor on Chevrolet Corvette?

Start replacement by taking off the front floor kick-up panel and cover from the ip electrical center. Unplug blo mot from the ip electrical center then disconnect the ip lower insulator panel on the right side. Unplug both electrical connectors from the Blower Motor resistor prior to unplugging it from the Blower Motor. Turn and slacken the forward two retaining screws of the Blower Motor resistor 5 mm then remove its rear screw. Lower the resistor's back end gently while keeping the attached hvac module part safe to pull the motor resistor out of the vehicle. Check if the Blower Motor resistor seal shows damage and order a new one if needed. Fit the upper part of the Blower Motor resistor into the hvac module while aligning its components. Then place the forward retaining slots of the resistor onto the screws and set the resistor in place. Set the rear screw into position and leave it light tight at first before turning all retaining screws to 1.6 n.m (14 lb in). First join the Blower Motor resistor to its electrical connector and second connect the wiring harness electrical connector to the Blower Motor resistor. Put back the ip lower insulator panel on the right side while also connecting the blo mot maxifuse #49 to its electric connections and replacing both the ip electrical cover and front floor kick-up panel.

OEM Chevrolet Corvette Blower Motor Resistor

Heater Blower Motor Resistor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Blower Motor Resistors found

View related parts
Chevrolet Corvette Power Module
Part Number: 12368387
$156.11 MSRP: $320.80
You Save: $164.69 (52%)
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Blower Motor Control; Module, A/C Electric Temperature And Motor Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1992 Chevrolet Corvette | Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module
Part Number: 16047800
$170.63 MSRP: $320.44
You Save: $149.81 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Ambient Temperature Sensor; Air Temperature Sensor; Power Module; In-Car Sensor; Module
- Replaced by: 12484912
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1989 Chevrolet Corvette | 35th Anniversary Edition, Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Resistor
Part Number: 14093106
$23.12 MSRP: $43.42
You Save: $20.30 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Blower Motor Resistor; Resistor, A/C Evaporator Blower; Resistor, Heater Blower Motor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1996 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Blower Motor Resistor
Part Number: 89019101
$54.16 MSRP: $101.70
You Save: $47.54 (47%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Resistor Assembly, Blower Motor; HVAC Blower Motor Resistor; Resistor; Resistor, A/C Evaporator Blower; Resistor, Heater Blower Motor
- Replaces: 15393829, 52481707, 89018501, 89018437, 12135102, 89018643, 15304891
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2003 Chevrolet Corvette | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module
Part Number: 89019166
Product Specifications
- Other Name: Module Assembly, Blower Motor Control; Blower Motor Resistor; Module; Resistor; Module, A/C Electric Temperature And Motor Control
- Replaces: 52479971, 52477902
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet Corvette | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Power Module
Part Number: 12368390
Product Specifications
- Other Name: Module Assembly, Blower Motor Control; Module, A/C Electric Temperature And Motor Control
- Replaces: 16174981
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Chevrolet Corvette | 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS

Chevrolet Corvette Blower Motor Resistor

Our website offers an extensive catalog of genuine Chevrolet Corvette Blower Motor Resistor at unbeatable prices. Every OEM Chevrolet Corvette Blower Motor Resistor comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Corvette Blower Motor Resistor Parts Questions & Experts Answers

Blower Motor Resistor
89019101
Q: How to replace the blower motor resistor on Chevrolet Corvette?
A: Start replacement by taking off the front floor kick-up panel and cover from the ip electrical center. Unplug blo mot from the ip electrical center then disconnect the ip lower insulator panel on the right side. Unplug both electrical connectors from the Blower Motor resistor prior to unplugging it from the Blower Motor. Turn and slacken the forward two retaining screws of the Blower Motor resistor 5 mm then remove its rear screw. Lower the resistor's back end gently while keeping the attached hvac module part safe to pull the motor resistor out of the vehicle. Check if the Blower Motor resistor seal shows damage and order a new one if needed. Fit the upper part of the Blower Motor resistor into the hvac module while aligning its components. Then place the forward retaining slots of the resistor onto the screws and set the resistor in place. Set the rear screw into position and leave it light tight at first before turning all retaining screws to 1.6 n.m (14 lb in). First join the Blower Motor resistor to its electrical connector and second connect the wiring harness electrical connector to the Blower Motor resistor. Put back the ip lower insulator panel on the right side while also connecting the blo mot maxifuse #49 to its electric connections and replacing both the ip electrical cover and front floor kick-up panel.