Make sure this part fits

GM 18046200
Caliper, Front Driver Side

1997-2005 GM

Customer Questions & Expert Answers (26)
GM 18046200 Caliper, Front Driver Side
  • Part Description
    Caliper, Front Brake; Brake Caliper
  • Position
    Front Driver Side
  • Replaces
    18024956
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    1997-2005 Buick CenturyCustom, Limited, Special Edition6 Cyl 3.1 L GAS
    2000-2005 Buick LeSabreCustom, Limited6 Cyl 3.8 L GAS
    1997-2004 Buick Regal25th Anniversary Edition, GS, GSE, LS, LSE6 Cyl 3.8 L GAS
    1997-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    1998-2002 Oldsmobile IntrigueBase, GL, GLS, GX6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
    1997-2004 Oldsmobile SilhouetteBase, GL, GLS, GS, Premiere6 Cyl 3.4 L GAS
    2000-2005 Pontiac BonnevilleSE6 Cyl 3.8 L GAS
    1997-2003 Pontiac Grand PrixGT, GTP, SE6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
    1999-2005 Pontiac MontanaBase6 Cyl 3.4 L GAS
    1997-1998 Pontiac Trans SportBase, Montana6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 18046200 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 18046200 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be inspected at the end of the process for the 2000 Buick Century? Posted by Customer
    A:
    Inspect the hydraulic brake system for any brake fluid leaks.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What tool is used to compress the caliper piston for the 2002 Buick LeSabre? Posted by Customer
    A:
    A large C-clamp.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the brake caliper piston bore and seal counterbore be cleaned for the 2005 Buick LeSabre? Posted by Customer
    A:
    Clean them with denatured alcohol or an equivalent, and dry them with non-lubricated, filtered air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be inspected on the caliper bore for the 2001 Buick Century? Posted by Customer
    A:
    Look for cracks, scoring, pitting, excessive rust, or corrosion.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step in the process for the 2000 Buick LeSabre? Posted by Customer
    A:
    Bleed the brake system, install the tire and wheel assembly, and finally lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after tightening the brake hose for the 2001 Buick LeSabre? Posted by Customer
    A:
    Reconnect the park brake cable to the park brake lever on the caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you remove the brake caliper piston from the caliper bore for the 2002 Buick Century? Posted by Customer
    A:
    Direct low-pressure compressed air into the bore through the fluid inlet hole.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the procedure for removing the brake caliper for the 2002 Buick LeSabre? Posted by Customer
    A:
    Remove the lower brake caliper pin bolt, rotate the caliper up, and take it off the upper pin bolt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after removing the C-clamp for the 2004 Buick Century? Posted by Customer
    A:
    Remove the brake hose-to-caliper bolt, discarding the 2 copper brake hose gaskets, and plug the opening in the rear brake hose to prevent excessive fluid loss and contamination.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if light rust or corrosion is found for the 2003 Buick Century? Posted by Customer
    A:
    Attempt to remove it with fine emery paper, but if imperfections persist or if severe damage is present, replace the caliper assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after removing the piston seal for the 2001 Buick Century? Posted by Customer
    A:
    Take out the bleeder valve and cap from the caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step to replace the front brake caliper for the 2001 Buick LeSabre? Posted by Customer
    A:
    Inspect the fluid level in the brake master cylinder reservoir.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done with the park brake lever for the 2004 Buick LeSabre? Posted by Customer
    A:
    Remove the return spring and the nut retaining the lever, then take off the lever.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the caliper bracket be installed for the 2002 Buick Regal? Posted by Customer
    A:
    Install the caliper bracket using the bracket bolts and tighten them to 115 Nm (85 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you detach the brake caliper for the 2000 Buick Regal? Posted by Customer
    A:
    Detach the hose bolt from the inlet fitting, then use a large C-clamp to push the caliper piston into the caliper bore.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after supporting the caliper for the 2003 Buick Regal? Posted by Customer
    A:
    Remove the rear brake pads, followed by the removal of the caliper bracket bolts and the caliper bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How can you identify the caliper pin bolts for the 2004 Buick Regal? Posted by Customer
    A:
    The leading caliper pin bolt has a bushing, and the trailing caliper pin bolt is solid.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you secure the rotor to the hub for the 2001 Buick Regal? Posted by Customer
    A:
    Hand tighten two wheel lug nuts to retain the rotor to the hub.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step in the process for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Inspect the fluid level in the brake master cylinder reservoir.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What tool should be used to remove the piston seal from the groove in the caliper bore for the 2003 Chevrolet Venture? Posted by Customer
    A:
    A small wooden or plastic tool.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be inspected in the caliper bore and seal grooves for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Inspect for scoring, nicks, corrosion, or wear.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the new caliper be installed for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Ensure the caliper bolt boots are properly installed, attach the caliper to the bracket, lubricate the brake caliper bolt shaft (without lubricating the bolt threads), and lubricate the brake caliper bolt boots in the caliper bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be inspected on the brake caliper piston for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Inspect for scoring, nicks, corrosion, or worn/damaged chrome plating, and replace it if any issues are found.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step in the assembly process for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Install the bleeder valve and cap back onto the caliper housing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step in brake caliper and knuckle maintenance for the 2000 Chevrolet Venture? Posted by Customer
    A:
    Remove and discard 1/3 of the brake fluid from the master cylinder using a suction gun.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Caliper, Front Driver Side 18046200 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 18046200 Caliper, Front Driver Side is available in the market under the name GM Brake Caliper Repair Kit, Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 18046200 Caliper, Front Driver Side fits certain Chevrolet Venture models, as well as Buick Regal, LeSabre, Century. Additionally, it is compatible with Pontiac Grand Prix, Bonneville, Montana and Oldsmobile Intrigue, Silhouette models.
The original GM component designated by manufacturer part number 18046200 maintains top performance when functioning as the Caliper, Front Brake; Brake Caliper unit at its Front Driver Side. The component 18046200 is constructed from durable material and its dimensions span 8.1 x 9.2 x 6.6 inches while weighing 10.10 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Caliper, Wheel Brake Cylinder/Caliper. The part 18046200 has available replacement options 18024956. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.