Make sure this part fits

GM 12607338
Heat Shield, Driver Side

2004-2010 GM

Customer Questions & Expert Answers (14)
GM 12607338 Heat Shield, Driver Side
  • Part Description
    Shield-Exhaust Manifold Heat; Exhaust Heat Shield
  • Position
    Driver Side
  • Replaces
    12567838
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2009 Cadillac SRXBase8 Cyl 4.6 L GAS
    2005-2010 Cadillac STSBase, Platinum, V8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 12607338 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12607338 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the torque specification for tightening the bolts during installation for the 2004 Cadillac SRX? Posted by Customer
    A:
    Tighten the bolts to 10 Nm (89 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What should be done after aligning the heat shield for the 2006 Cadillac SRX? Posted by Customer
    A:
    Install the bolts securing the center bearing heat shield to the center bearing and tighten them to 8 Nm (71 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the first step to replace the exhaust heat shield for the center bearing for the 2007 Cadillac SRX? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the final step after installing the heat shield for the 2008 Cadillac STS? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the torque specification for tightening the exhaust manifold heat shield bolts for the 2008 Cadillac STS? Posted by Customer
    A:
    Tighten them to 10 N.m (89 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the first step for installation of the new heat shield for the 2009 Cadillac SRX? Posted by Customer
    A:
    Slide the new heat shield in between the body, the drive shaft center bearing, and the exhaust pipes.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    How should the new heat shield be aligned for the 2005 Cadillac STS? Posted by Customer
    A:
    Align the holes in the heat shield with those in the center bearing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the process for installing the new heat shield for the 2008 Cadillac SRX? Posted by Customer
    A:
    Slide the new heat shield in between the body, the drive shaft center bearing, and the exhaust pipes, ensuring the holes in the heat shield align with those in the center bearing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the torque specification for tightening the bolts for the 2005 Cadillac SRX? Posted by Customer
    A:
    Tighten them to 10 Nm (89 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What safety equipment should be worn during this procedure for the 2009 Cadillac STS? Posted by Customer
    A:
    Always wear protective goggles and gloves.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What should be done after tightening all bolts for the 2009 Cadillac SRX? Posted by Customer
    A:
    Reconnect the center intermediate shaft to the lower intermediate shaft, lower the vehicle, and finally remove the J 42640.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What should be done after removing the bolts for the 2007 Cadillac STS? Posted by Customer
    A:
    Take off the exhaust manifold heat shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    Q:
    What is the first step to replace the exhaust heat shield for the center bearing for the 2006 Cadillac STS? Posted by Customer
    A:
    Raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Exhaust Heat Shield
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Heat Shield, Driver Side 12607338 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12607338 Heat Shield, Driver Side is available in the market under the name GM Exhaust Heat Shield. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12607338 Heat Shield, Driver Side fits certain Cadillac SRX, STS models.
The original GM component designated by manufacturer part number 12607338 maintains top performance when functioning as the Shield-Exhaust Manifold Heat; Exhaust Heat Shield unit at its Driver Side. The component 12607338 is constructed from durable material and its dimensions span 20.2 x 11.9 x 5.4 inches while weighing 1.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Shield, Exhaust Manifold. The part 12607338 has available replacement options 12567838. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.