GM 15236987
Front Driver Speaker

The replacement of the front floor console subwoofer speaker requires users to begin by taking out the 2 front seats then pushing back the Center Console to remove its wire connector. The console needs further movement backward to reach the subwoofer speaker as you disconnect its wire connector after removing all 4 retaining bolts. Install the new speaker into the subwoofer assembly, connect the wire connector then install the 4 retaining screws using the same thread path in the screw boss before tightening each screw to 6 n.m (53 lb in). For completion of the procedure reposition the console to reattach the wire connector before you reinstall the i/p console and the 2 front seats.

The first step to change the front floor console subwoofer speaker involves disassembling the 2 front seats. Initiate the subwoofer speaker replacement by pushing the Center Console to disconnect its wire connector before moving further to expose the subwoofer speaker. First disconnect the wire connector from the speaker and then remove the 4 retaining bolts to take out the speaker from the subwoofer assembly. Put the speaker inside the subwoofer assembly before connecting its wire connector. Screw in the four retaining screws while keeping them on the original thread path in the screw bosses and torques them to 6 n.m (53 lb in). First move the console forward to reconnect the wire connector and afterwards install the console to the i/p and install the 2 front seats.

The first step to replace the radio front floor console speaker (Subwoofer Speaker) begins with seat removal from both the front positions. Gently push forward on the Center Console unit until you disconnect the wire connector before progressing the console backward to reach the subwoofer speaker. Remove the speaker through disconnecting the wire connector after you remove the 4 retaining bolts. Put the speaker in the subwoofer assembly before connecting the wire connector according to the fastener notice specifications. Add the four retaining screws by following the same thread pattern in the screw boss while tightening them to 6 n.m (53 lb in). Reconnect the wire connector when the console moves forward. After this, mount the console on the instrument panel before reinstalling both front seats.

You should start your Radio Front Side Door Speaker replacement process by taking out the trim panel. Press down on the top retainer to disconnect the speaker while simultaneously removing it from its position. After that disconnect the electrical connector. Start by attaching the electrical connector before you attach the speaker through its snap function until it reaches full seating. After replacing the component you should reinstall the trim panel then verify proper functioning of all parts.

The speaker replacement of the front door starts by taking off the trim panel. The speaker removal starts with lowering the top retainer before the speaker can be extracted and its electrical connector must be disconnected. When installing the component connect the electrical connector then push the speaker to its full position. After installation of the trim panel check that all components function correctly.

Start the door speaker replacement process by taking away the trim panel. After that, use your finger to press in the discreet tab located at the top of the speaker to easily detach it and separate it from the connector cable. To install the new speaker, first attach the electrical connector and then press the speaker squarely into the housing. Once all the parts are back in place, test the speaker by turning on the system.

Reinstall the door trim panel and verify the component operation.

Reinstall the door trim panel and ensure to verify the operation of the component after installation.

Remove the door trim panel.

Remove the speaker from the mounting bracket and, if necessary, take out the bolts that hold the speaker mounting bracket to the door before removing the bracket itself.

Verify the component's operation after installation.

First, remove the trim panel.

Position the speaker mounting bracket and, if it was removed, install the bolts to secure it to the door, tightening them to 6 N.m (53 lb in).

Secure the speaker with the screws, tightening them to 2 N.m (53 lb in).

Reinstall the door trim panel and verify the component's operation.

Connect the electrical connectors as needed, install the speaker, and then reinstall the garnish molding.

Attach the speaker to the mounting bracket and reconnect the electrical connector.

Press the speaker out of the molding.

Connect the electrical connector.

Reconnect the electrical connector.

Connect the electrical connectors as needed, install the speaker, and then reinstall the garnish molding.

Verify the component's operation.

Move the console forward to connect the wire connector, install the console to the I/P, and finally reinstall the 2 front seats.