GM 15206533
Window Switch, Rear Driver Side

Users can remove the door power window switch from the trim panel by using a flat-bladed tool followed by disconnecting its electrical connector before replacing the switch. First connect the electric wires to the switch then embed the switch firmly onto the door trim panel until it reaches complete seating.

One must start the process by extracting the front door trim panel followed by unplugging electrical connectors during the driver side Door Lock and side window switch replacement. The screw that holds the switch panel bezel to the front door panel should be removed before you use a flat-bladed tool to detach the bezel from the panel. A wide plastic flat-bladed tool should be used to release retaining clips on both sides of the door module before removing it from the switch panel bezel. Put the door module into the switch panel bezel framework and secure by snapping it in. Afterward attach both components to the door panel. The screw must be installed to fasten the switch panel bezel onto the front door panel while using 2 n.m (18 lb in) torque. After reconnecting the electrical connections users should replace the front door trim panel. The service programming system (SPS) should be used to program the door module when performing this operation on vehicles with camper mirrors.

The first step for replacing the driver side Door Lock and side window switch involves removing the front door trim panel before disconnecting electrical connectors. First dismantle the front door panel by removing the screw that maintains the switch panel bezel then separate the bezel carefully with a flat-bladed tool. The wide plastic flat-bladed tool should be used to disengage retaining clips along both door module sides before getting the door module out of the switch panel bezel. Position the door module inside the switch panel bezel so it will snap-lock before you connect the bezel with the module to its designated spot on the door panel. Secure the switch panel bezel retaining screw onto the front door panel while torquing it to 2 n.m (18 lb in). Join all electrical connections before you return the front door trim panel back into position. Proceed with programming the door module when the vehicle contains camper mirrors. You will find programming and setup data in corresponding documentation.

The first procedure for changing the rear door power window switch consists of using a small flat-bladed tool to gently remove the door power window switch from the door trim panel. The first step should involve removing the electrical connector link from the switch. Installation requires fitting the electrical connector to the switch before pressing the switch into the door trim panel with full seating.

The procedure for replacing the rear side door window switch requires a small flat-bladed tool to separate the door power window switch from behind the door trim panel. Eliminate the electrical connection from the switch. You should connect the electrical connector to the switch before pressing it into the door trim panel until complete insertion.

The first procedure for changing the rear door power window switch consists of using a small flat-bladed tool to gently remove the door power window switch from the door trim panel. The first step should involve removing the electrical connector link from the switch. Installation requires fitting the electrical connector to the switch before pressing the switch into the door trim panel with full seating.

Before starting to replace the driver side Door Lock and side window switch one must first remove the front door trim panel and next disconnect electrical connectors. The first step involves removing the screw which holds the switch panel bezel to the front door panel and you should carefully use a flat-bladed tool to remove the switch panel bezel. A wide plastic flat-bladed tool serves to let go of retaining clips running along both sides of the door module before you can pull out the door module from the switch panel bezel. To install the door module fit it into the switch panel bezel before it snaps securely in place and attach the bevelled module to the door panel. Install the switch panel bezel to the front door panel using the screw while achieving a torque of 2 n.m that is equivalent to 18 lb in. Place the electrical wires back in place followed by reinstalling the front door trim panel. Programming of door modules requires the service programming system when camper mirrors are present on the vehicle.

The procedure for replacing the rear side door window switch requires a small flat-bladed tool to separate the door power window switch from behind the door trim panel. Eliminate the electrical connection from the switch. You should connect the electrical connector to the switch before pressing it into the door trim panel until complete insertion.

Starting your driver side front door switch and lock replacement procedure requires you to remove the door trim panel and disconnect the wiring connectors. The screw retaining the switch panel bezel from the front door panel should be removed first followed by gentle detachment of the bezel with a flat-bladed tool. A wide plastic flat-bladed tool should be used to release retaining clips which are located on both sides of the door module before removing it from the switch panel bezel. The door module should be inserted into the switch panel bezel until it snaps before attaching the bezel and module to the door panel. Embed the switch panel bezel to the front door panel by tightening its screw to 2 n.m (18 lb in). Restore the electrical connections before putting back the front door trim panel. The service programming system (SPS) should be used to program the door module on vehicles with camper mirrors.

The first procedure for changing the rear door power window switch consists of using a small flat-bladed tool to gently remove the door power window switch from the door trim panel. The first step should involve removing the electrical connector link from the switch. Installation requires fitting the electrical connector to the switch before pressing the switch into the door trim panel with full seating.

Ensure to program the door module accordingly.

Disconnect the electrical connector from the switch.

A wide plastic flat-bladed tool is recommended to release the retaining clips.

First, remove the front door trim panel.