Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 88957259
Hub & Bearing

1997-2005 GM

Customer Questions & Expert Answers (9)
GM 88957259 Hub & Bearing
GM 88957259 Hub & Bearing
GM 88957259 Hub & Bearing
GM 88957259 Hub & Bearing
GM 88957259 Hub & Bearing
GM 88957259 Hub & Bearing
  • Part Description
    Hub Kit, Front Wheel; Wheel Bearing & Hub Assembly; Wheel Hub Repair Kit; Axle Bearing.
  • Position
    Front
  • Replaces
    07470561, 07470018, 12429201, 12429202, 7470561, 7470018
  • Manufacturer
    General Motors
Make sure this part fits
$122.85 MSRP: $363.66
You Save: $240.81 (67%)
1
ADD TO CART

  • 88957259 Hub & Bearing is Ref No. 3 in the diagram below

    2002 Chevy Malibu Hub & Bearing Diagram for 88957259
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 88957259

  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2005 Chevrolet ClassicBase, LS4 Cyl 2.2 L GAS
    1997-2003 Chevrolet MalibuBase, LS4 Cyl 2.4 L GAS, 6 Cyl 3.1 L GAS
    1999-2004 Oldsmobile AleroGL, GLS, GX4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.4 L GAS
    1997-1999 Oldsmobile CutlassBase, GL, GLS6 Cyl 3.1 L GAS
    1997 Oldsmobile Cutlass SupremeBase6 Cyl 3.1 L GAS
    1999-2005 Pontiac Grand AmGT, GT1, SE, SE1, SE24 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.4 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is 88957259 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88957259 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front wheel hub and bearing on Chevrolet Classic? Posted by Customer
    A:
    Start by raising the vehicle and removing the wheel assembly and tire before you can begin working on the front Wheel Bearing and hub. Start by removing the wheel drive shaft nut followed by the brake rotor. Detach the hub and bearing assembly from the Steering Knuckle after removing the hub and bearing assembly bolts. The installation of the hub and bearing assembly to the Steering Knuckle requires you to tighten the hub and bearing assembly bolts to 95 nm (70 ft. Lbs.). The next steps should be to install the brake rotor followed by the wheel drive shaft nut then the tire and wheel assemblies. The final test involves checking the front wheel alignment.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear wheel bearing and hub on Chevrolet Classic? Posted by Customer
    A:
    After properly supporting the vehicle, you must first take off the tire and wheel assemblies during replacement of the rear Wheel Bearing and hub. Handle the Brake Drum with care to shield the bearing against damage before you take off the Brake Drum. First unfasten half of the hub and bearing assembly while looking after the top rear nut to access the Brake Shoe. Unplug the wire connection from the abs sensor at the rear and take out the hub and bearing unit from your vehicle. Before assembly place the top rear bolt in its position in the hub and bearing assembly before installing it into the axle unit. Install the hub bolts to 85 nm torque and put on the Brake Drum afterward you can add wheels plus tires before lowering the vehicle to its normal position.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear wheel hub and bearing on Chevrolet Classic? Posted by Customer
    A:
    To perform the Wheel Bearing and hub replacement work first support and lift the vehicle then take out the wheel and tire parts. When handling the Brake Drum do not strike it directly to protect the bearing and remove the component next. Begin by taking out part of the hub-and-bearing assembly from the axle then work toward removing the top rear bolt and nut since they remain caught by the Brake Shoe. Unplug the sensor wire from the abs wheel speed system and take out all parts of the hub and bearing assembly. After wiring the abs sensor tap, install the hub and bearing unit while setting the first bolt in place first before placing it into the axle. After applying the specified torque to hub bolts install the Brake Drum then put on tires and wheels before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear wheel bearing and wheel hub on Chevrolet Malibu? Posted by Customer
    A:
    To replace the rear wheel bearing and hub you must first lift the vehicle properly while keeping it supported then carefully detach both tire and wheel components with special attention to avoid damaging the bearing through hammering on the Brake Drum. First separate the Brake Drum then pull out the axle assembly from its position. You must first get the hub and bearing assembly partly out before removing its top rear bolt and threaded nut due to Brake Shoe interference. Disconnect the rear abs sensor wires first to take out the complete hub and bearing assembly from the vehicle. Reattach the rear abs speed sensor wire connector before mounting the new hub and bearing assembly into the axle space. Locate the top rear bolt inside the assembly before locking it in position and tightening the hub bolts to 85 newton meters. Fix the Brake Drum then put on tires and wheels before allowing the car to rest on the ground.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after installing the hub and bearing assembly for the 2004 Chevrolet Classic? Posted by Customer
    A:
    Reinstall the brake rotor, the wheel drive shaft nut, and the tire and wheel assemblies.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    How should the hub and bearing assembly be removed from the axle for the 2000 Chevrolet Malibu? Posted by Customer
    A:
    Partially remove the assembly before taking out the top rear attaching bolt and nut to clear the brake shoe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What is the next step after removing the brake rotor for the 2003 Chevrolet Malibu? Posted by Customer
    A:
    Remove the hub and bearing assembly bolts and detach the hub and bearing assembly from the steering knuckle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Hub
    Q:
    What is the first step in the installation process for the 2001 Chevrolet Malibu? Posted by Customer
    A:
    Reconnect the rear ABS wheel speed sensor wire connector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Hub & Bearing 88957259 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88957259 Hub & Bearing is available in the market under the name GM Wheel Bearing, Wheel Hub. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88957259 Hub & Bearing fits certain Chevrolet Malibu, Classic models, as well as Pontiac Grand Am. Additionally, it is compatible with Oldsmobile Cutlass, Alero, Cutlass Supreme models.
The original GM component designated by manufacturer part number 88957259 maintains top performance when functioning as the Hub Kit, Front Wheel; Wheel Bearing & Hub Assembly; Wheel Hub Repair Kit; Axle Bearing. unit at its Front. The component 88957259 is constructed from durable material and its dimensions span 7.0 x 6.9 x 6.8 inches while weighing 7.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 88957259 has available replacement options 07470561, 07470018, 12429201, 12429202, 7470561, 7470018. Each vehicle needs 2 units of the part marked as SKU 88957259. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.