How to overhaul the front brake calipers on 2001 Buick LeSabre?

You should start by removing the caliper from your vehicle but avoid placing your fingers in front of the Piston and use compressed air carefully to prevent injuries. The interior of the caliper housing requires clean cloth padding while holding a low-pressure compressed air stream through the fluid inlet hole to avoid damaging the pistons by blowing them out of their bores. Use a small wooden or plastic tool to take out the Piston dust boot seal and Piston seal from the caliper before discarding them. Pull out the bleeder valve and attach the cap to the caliper . It is important to clean the Brake Caliper Piston bore and seal counterbore alongside caliper Piston with denatured alcohol or equivalent until they are dry by filtering and non-lubricated air. You must examine the caliper bore for evidence of cracks or scoring or pitting or excessive rust or corrosion. When lightly rusty or corroded areas exist, try cleaning them with fine emery paper before deciding to replace the caliper assembly as a whole. Check the caliper Piston for any indications of cracking, scoring or damaged chrome plating before needing a replacement. You should apply delco supreme 11 (R) (GM P/N 12377967) or equivalent dot-3 brake fluid from a clean, sealed container to the new Piston seal before installing it into the caliper bore. Position the caliper Piston inside the bore and place the new Piston dust boot seal over the Piston before seating the dust boot seal completely through the use of a caliper Piston dust boot seal installer or equivalent tool designed for 78.08 mm (3.074 inch) counterbore and 63.52 mm (2.501 inch) Piston bore diameters. Install the bleeder valve along with its cap on the caliper before securing the valve tightly and reinstalling the caliper to the vehicle.

OEM 2001 Buick LeSabre Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Calipers found

View related parts
2001 Buick LeSabre Caliper, Front Driver Side Part Number: 18046196
$145.18 MSRP: $284.26
You Save: $139.08 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18029818
- Item Weight: 9.80 Pounds
- Item Dimensions: 9.5 x 8.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046196
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Caliper, Front Passenger Side Part Number: 18046197
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18029819
- Item Weight: 10.40 Pounds
- Item Dimensions: 7.8 x 9.0 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046197
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Caliper Part Number: 89047651
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18042413
- Item Weight: 6.70 Pounds
- Item Dimensions: 9.6 x 7.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89047651
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Caliper Part Number: 89047652
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18042414
- Item Weight: 6.20 Pounds
- Item Dimensions: 9.8 x 7.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89047652
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Caliper, Front Passenger Side Part Number: 18046201
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18024957
- Item Weight: 10.80 Pounds
- Item Dimensions: 7.9 x 8.9 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046201
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Caliper, Front Driver Side Part Number: 18046200
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18024956
- Item Weight: 10.10 Pounds
- Item Dimensions: 8.1 x 9.2 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046200
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Overhaul Kit, Rear Part Number: 18042415
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Item Weight: 0.40 Pounds
- Item Dimensions: 4.7 x 3.3 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 18042415
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2001 Buick LeSabre Overhaul Kit, Front Part Number: 18017156
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Wheel Brake Cylinder/Caliper Piston Kit.
- Position: Front
- Replaces: 18024958
- Item Weight: 0.30 Pounds
- Item Dimensions: 3.9 x 3.8 x 0.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 18017156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS

2001 Buick LeSabre Brake Calipers

With a comprehensive array of OEM 2001 Buick LeSabre Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2001 Buick LeSabre Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2001 Buick LeSabre Brake Calipers Parts and Q&A

Q: How to overhaul the front brake calipers on 2001 Buick LeSabre?
A: You should start by removing the caliper from your vehicle but avoid placing your fingers in front of the Piston and use compressed air carefully to prevent injuries. The interior of the caliper housing requires clean cloth padding while holding a low-pressure compressed air stream through the fluid inlet hole to avoid damaging the pistons by blowing them out of their bores. Use a small wooden or plastic tool to take out the Piston dust boot seal and Piston seal from the caliper before discarding them. Pull out the bleeder valve and attach the cap to the caliper . It is important to clean the Brake Caliper Piston bore and seal counterbore alongside caliper Piston with denatured alcohol or equivalent until they are dry by filtering and non-lubricated air. You must examine the caliper bore for evidence of cracks or scoring or pitting or excessive rust or corrosion. When lightly rusty or corroded areas exist, try cleaning them with fine emery paper before deciding to replace the caliper assembly as a whole. Check the caliper Piston for any indications of cracking, scoring or damaged chrome plating before needing a replacement. You should apply delco supreme 11 (R) (GM P/N 12377967) or equivalent dot-3 brake fluid from a clean, sealed container to the new Piston seal before installing it into the caliper bore. Position the caliper Piston inside the bore and place the new Piston dust boot seal over the Piston before seating the dust boot seal completely through the use of a caliper Piston dust boot seal installer or equivalent tool designed for 78.08 mm (3.074 inch) counterbore and 63.52 mm (2.501 inch) Piston bore diameters. Install the bleeder valve along with its cap on the caliper before securing the valve tightly and reinstalling the caliper to the vehicle.