How to replace the rear brake calipers on 2000 Buick LeSabre?

You should extract two-thirds of the brake fluid from the master cylinder before replacing the rear brake caliper. Secure the vehicle with raised supports while removing the wheel with its tire. A screwdriver or pry bar must not be used to compress the caliper piston to prevent boot damage which could result in future corrosion. A maximum 1 mm piston travel is necessary to avoid internal adjusting damage from occurring. A large c clamp should be used to push and compress the caliper piston into the caliper bore until light resistance is felt. Make sure the piston travel stays within 1 mm. Next-step caliper repair requires removal of the bolt sustaining the inlet fitting but users must create a seal to block fluid waste and outside contaminants. Pull the park brake cable out of the caliper before removing the lower caliper pin bolt. Adjust the caliper onto the upper pin and then pull it down from above. To install the caliper simply position it atop the top caliper slide pin so the caliper piston cutouts match the locating pins on the Brake Pad. Set the caliper into position with brake pads at the caliper bracket before tightening the lower caliper pin to 27 nm torque (20 ft. Lbs.) via a torque wrench. Put the brake hose inlet fitting onto the caliper while tightening the fitting bolt to 45 nm (33 ft. Lbs.) then connect the park brake cable back to the caliper. After bleeding the brake system the technician must start the vehicle while applying 778 nm (175 lb. Ft.) of force to the Brake Caliper Piston and pads three times to safely install them. After verifying brake fluid, reinstall the tire-wheel setup and finally lower the vehicle.

OEM 2000 Buick LeSabre Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Calipers found

View related parts
2000 Buick LeSabre Caliper, Front Driver Side Part Number: 18046196
$145.18 MSRP: $284.26
You Save: $139.08 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18029818
- Item Weight: 9.80 Pounds
- Item Dimensions: 9.5 x 8.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046196
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Caliper, Front Passenger Side Part Number: 18046197
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18029819
- Item Weight: 10.40 Pounds
- Item Dimensions: 7.8 x 9.0 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046197
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Caliper Part Number: 89047651
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18042413
- Item Weight: 6.70 Pounds
- Item Dimensions: 9.6 x 7.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89047651
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Caliper Part Number: 89047652
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18042414
- Item Weight: 6.20 Pounds
- Item Dimensions: 9.8 x 7.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89047652
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Caliper, Front Passenger Side Part Number: 18046201
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18024957
- Item Weight: 10.80 Pounds
- Item Dimensions: 7.9 x 8.9 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046201
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Caliper, Front Driver Side Part Number: 18046200
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18024956
- Item Weight: 10.10 Pounds
- Item Dimensions: 8.1 x 9.2 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18046200
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Overhaul Kit, Rear Part Number: 18042415
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Item Weight: 0.40 Pounds
- Item Dimensions: 4.7 x 3.3 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 18042415
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
2000 Buick LeSabre Overhaul Kit, Front Part Number: 18017156
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Wheel Brake Cylinder/Caliper Piston Kit.
- Position: Front
- Replaces: 18024958
- Item Weight: 0.30 Pounds
- Item Dimensions: 3.9 x 3.8 x 0.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 18017156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Buick LeSabre Submodels:
- Custom, Limited | 6 Cyl 3.8 L GAS

2000 Buick LeSabre Brake Calipers

With a comprehensive array of OEM 2000 Buick LeSabre Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 Buick LeSabre Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2000 Buick LeSabre Brake Calipers Parts and Q&A

Q: How to replace the rear brake calipers on 2000 Buick LeSabre?
A: You should extract two-thirds of the brake fluid from the master cylinder before replacing the rear brake caliper. Secure the vehicle with raised supports while removing the wheel with its tire. A screwdriver or pry bar must not be used to compress the caliper piston to prevent boot damage which could result in future corrosion. A maximum 1 mm piston travel is necessary to avoid internal adjusting damage from occurring. A large c clamp should be used to push and compress the caliper piston into the caliper bore until light resistance is felt. Make sure the piston travel stays within 1 mm. Next-step caliper repair requires removal of the bolt sustaining the inlet fitting but users must create a seal to block fluid waste and outside contaminants. Pull the park brake cable out of the caliper before removing the lower caliper pin bolt. Adjust the caliper onto the upper pin and then pull it down from above. To install the caliper simply position it atop the top caliper slide pin so the caliper piston cutouts match the locating pins on the Brake Pad. Set the caliper into position with brake pads at the caliper bracket before tightening the lower caliper pin to 27 nm torque (20 ft. Lbs.) via a torque wrench. Put the brake hose inlet fitting onto the caliper while tightening the fitting bolt to 45 nm (33 ft. Lbs.) then connect the park brake cable back to the caliper. After bleeding the brake system the technician must start the vehicle while applying 778 nm (175 lb. Ft.) of force to the Brake Caliper Piston and pads three times to safely install them. After verifying brake fluid, reinstall the tire-wheel setup and finally lower the vehicle.