How to replace the front brake calipers on 2005 Buick Rendezvous?

Before replacing the front brake caliper you need to check the brake master cylinder reservoir fluid and drain it to match the midway level. Before starting work hoist the vehicle up and take off both the tire and wheel assembly. Place a large c-clamp over the brake caliper top and tighten it until its piston moves toward the bore space. Install two brake rotor lug nuts to hold the hub together before removing the caliper. You need to pull the brake hose bolt and hose section from the brake caliper while discarding the contact between the copper brake hose gaskets fixed to either component. Seal the brake caliper and hose connections before cleaning the affected brake hose area. Take off the caliper from its bracket by loosening its brake bolts. Check the brake caliper pin boots for damage and replace them if needed. Also clean and replace caliper pins when they show signs of corrosion. To install the caliper position the boot correctly before attaching it to the caliper bracket. Tighten the brakes caliper bolts to 54 nm (40 ft. Lbs.). Put new brake hose gaskets on the brake hose end before connecting the brake hose bolt to the brake hose . Tighten the bolt to 54 nm (40 ft. Lbs.). Put the tire wheel on and lower the car while filling the brake system to its required level. Also bleed the brake system afterward. Press the brake pedal 778 nm (175 ft. Lbs.) against the force for 10 seconds then check for leaks from the brake caliper and hydraulic brake parts.

OEM 2005 Buick Rendezvous Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Brake Calipers found

View related parts
2005 Buick Rendezvous Caliper Overhaul Kit, Rear
Part Number: 18023387
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper Piston; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Item Weight: 0.40 Pounds
- Item Dimensions: 9.2 x 7.9 x 6.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18023387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2005 Buick Rendezvous Caliper, Passenger Side
Part Number: 10434251
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Item Weight: 10.40 Pounds
- Item Dimensions: 7.1 x 4.0 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10434251
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2005 Buick Rendezvous Caliper, Driver Side
Part Number: 10434252
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Item Weight: 11.10 Pounds
- Item Dimensions: 10.4 x 9.1 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10434252
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2005 Buick Rendezvous Caliper, Passenger Side
Part Number: 18044881
Product Specifications
- Other Name: Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Item Weight: 5.50 Pounds
- Item Dimensions: 9.9 x 7.4 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18044881
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2005 Buick Rendezvous Caliper, Driver Side
Part Number: 18044880
Product Specifications
- Other Name: Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Item Weight: 4.50 Pounds
- Item Dimensions: 9.6 x 7.6 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18044880
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS

2005 Buick Rendezvous Brake Calipers

With a comprehensive array of OEM 2005 Buick Rendezvous Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2005 Buick Rendezvous Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2005 Buick Rendezvous Parts Questions & Experts Answers

Q: How to replace the front brake calipers on 2005 Buick Rendezvous?
A: Before replacing the front brake caliper you need to check the brake master cylinder reservoir fluid and drain it to match the midway level. Before starting work hoist the vehicle up and take off both the tire and wheel assembly. Place a large c-clamp over the brake caliper top and tighten it until its piston moves toward the bore space. Install two brake rotor lug nuts to hold the hub together before removing the caliper. You need to pull the brake hose bolt and hose section from the brake caliper while discarding the contact between the copper brake hose gaskets fixed to either component. Seal the brake caliper and hose connections before cleaning the affected brake hose area. Take off the caliper from its bracket by loosening its brake bolts. Check the brake caliper pin boots for damage and replace them if needed. Also clean and replace caliper pins when they show signs of corrosion. To install the caliper position the boot correctly before attaching it to the caliper bracket. Tighten the brakes caliper bolts to 54 nm (40 ft. Lbs.). Put new brake hose gaskets on the brake hose end before connecting the brake hose bolt to the brake hose . Tighten the bolt to 54 nm (40 ft. Lbs.). Put the tire wheel on and lower the car while filling the brake system to its required level. Also bleed the brake system afterward. Press the brake pedal 778 nm (175 ft. Lbs.) against the force for 10 seconds then check for leaks from the brake caliper and hydraulic brake parts.