Make sure this part fits

GM 18044881
Caliper, Passenger Side

2000-2007 GM

Customer Questions & Expert Answers (15)
GM 18044881 Caliper, Passenger Side
  • Part Description
    Brake Caliper
  • Position
    Passenger Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2007 Buick RendezvousCX, CX Plus, CXL, CXL Plus, Ultra6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
    2000-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    2000-2004 Oldsmobile SilhouetteGL, GLS, Premiere6 Cyl 3.4 L GAS
    2001-2005 Pontiac AztekBase, GT, Rally6 Cyl 3.4 L GAS
    2000-2005 Pontiac MontanaBase6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 18044881 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 18044881 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is important during the installation of the new brake caliper for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Ensure the caliper bolt bushings and boots are properly installed, then attach the brake caliper to the bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What are the final steps after securing the brake hose for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Remove the nuts securing the rotor to the hub, install the tire and wheel, lower the vehicle, fill the master cylinder to the proper level, and bleed the brake system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done with the brake hose for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Remove the brake hose bolt and the brake hose from the brake caliper, discarding the two copper brake hose gaskets that may be stuck to the caliper or hose end.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should light corrosion be treated for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Polish out light corrosion with crocus cloth, but replace the caliper if the corrosion is severe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after supporting the brake caliper for the 2004 Buick Rendezvous? Posted by Customer
    A:
    Remove the caliper from the mounting bracket without disconnecting the hydraulic brake flexible hose, then take out the rear brake pads.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What are the final steps after reassembling the brake components for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Remove the nuts securing the rotor to the hub, install the tire and wheel, lower the vehicle, fill the master cylinder to the proper level, and bleed the brake system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step in the process for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Install and tighten the bleeder valve and cap to the caliper, then reinstall the rear brake caliper to the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the new piston seal be prepared before installation for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Lubricate it with Delco Supreme 11(R) GM P/N 12377967 (Canadian P/N 992667) or equivalent DOT-3 brake fluid.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after removing the brake fluid for the 2000 Chevrolet Venture? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be removed from the brake caliper housing before cleaning for the 2003 Chevrolet Venture? Posted by Customer
    A:
    The bleeder valve cap and bleeder valve.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you clean the caliper housing and bleeder valve for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Use filtered, non-lubricated compressed air to blow out all passages in the caliper housing and bleeder valve.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What precautions should be taken after removing the brake hose for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Plug the openings in the brake caliper and hose to prevent fluid loss and contamination, then clean any dirt or corrosion near the brake hose fitting.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step in the assembly process for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Install the caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if the fluid level is above midway for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Remove brake fluid to that midway point.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Caliper, Passenger Side 18044881 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 18044881 Caliper, Passenger Side is available in the market under the name GM Brake Caliper Repair Kit, Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 18044881 Caliper, Passenger Side fits certain Chevrolet Venture models, as well as Buick Rendezvous. Additionally, it is compatible with Pontiac Aztek, Montana and Oldsmobile Silhouette models.
The original GM component designated by manufacturer part number 18044881 maintains top performance when functioning as the Brake Caliper unit at its Passenger Side. The component 18044881 is constructed from durable material and its dimensions span 9.9 x 7.4 x 5.4 inches while weighing 5.50 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Caliper, Wheel Brake Cylinder/Caliper. The part 18044881 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.