Make sure this part fits

GM 18044880
Caliper, Driver Side

2000-2007 GM

Customer Questions & Expert Answers (15)
GM 18044880 Caliper, Driver Side
  • Part Description
    Brake Caliper
  • Position
    Driver Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2007 Buick RendezvousCX, CX Plus, CXL, CXL Plus, Ultra6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
    2000-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    2000-2004 Oldsmobile SilhouetteGL, GLS, Premiere6 Cyl 3.4 L GAS
    2001-2005 Pontiac AztekBase, GT, Rally6 Cyl 3.4 L GAS
    2000-2005 Pontiac MontanaBase6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 18044880 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 18044880 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done before removing the brake caliper for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Clean any dirt or corrosion near the brake hose fitting, then remove the brake caliper bolts and take off the brake caliper from the bracket, inspecting the caliper bracket bolt boot for cuts, tears, or deterioration, and replace any damaged boots.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after installing the caliper for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Remove the plugs from the brake hose end, install new copper brake hose gaskets, and assemble the brake hose bolt with the gaskets, tightening the bolt to 54 Nm (40 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should you check for after removing the piston seal for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Inspect the bore and seal grooves for damage.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should not be used for cleaning the brake caliper piston for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Do not use abrasives for cleaning the brake caliper piston.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the caliper bracket be installed for the 2004 Buick Rendezvous? Posted by Customer
    A:
    Install the caliper bracket using the bolts and tighten them to 130 Nm (96 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the torque specification for the brake caliper bolts for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Tighten the brake caliper bolts to 45 N.m (33 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you prevent fluid loss and contamination for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Plug the openings in the brake caliper and hose.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after checking the brake pads for the 2000 Chevrolet Venture? Posted by Customer
    A:
    Remove the brake pads and brake pad retainers, then clean the brake caliper bracket and pads with a wire brush to remove rust and debris.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be checked regarding the brake caliper bolt boots for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Inspect and replace any that show cuts, tears, or deterioration.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step in servicing and repairing the front brake caliper for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Begin by removing the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after reinstalling the tire and wheel for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Lower the vehicle and fill the master cylinder to the proper level.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should not be attempted on the brake caliper bolt pin boots for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Polishing away any corrosion.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if corrosion is found on the caliper bolts for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Replace the brake caliper bolt, brake caliper bolt bushing, and brake caliper bolt boot without attempting to polish the corrosion away.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the first step to overhaul the rear brake caliper for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Remove the brake caliper while ensuring not to place fingers in front of the caliper piston(s) when applying compressed air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Caliper, Driver Side 18044880 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 18044880 Caliper, Driver Side is available in the market under the name GM Brake Caliper Repair Kit, Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 18044880 Caliper, Driver Side fits certain Chevrolet Venture models, as well as Buick Rendezvous. Additionally, it is compatible with Pontiac Aztek, Montana and Oldsmobile Silhouette models.
The original GM component designated by manufacturer part number 18044880 maintains top performance when functioning as the Brake Caliper unit at its Driver Side. The component 18044880 is constructed from durable material and its dimensions span 9.6 x 7.6 x 5.2 inches while weighing 4.50 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Caliper, Wheel Brake Cylinder/Caliper. The part 18044880 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.