How to Replace a Power Steering Hose on 2006 Chevrolet Uplander?

The first step to change the power steering cooler pipe/hose requires lifting and supporting the vehicle followed by right side engine splash shield removal. A drain pan should be placed under the Power Steering Pump and gear while you disconnect the return hose from the cooler pipe. Steering control loss can result from damage so the intermediate shaft must be disconnected from the steering gear. A utility stand should support the frame's rear while you remove frame bolts to lower the back section below clearance level. The first step requires the power steering gear heat shield removal along with the hose clip before disconnecting the cooler pipe from the steering gear while extracting the retainer bolt/screw and retainer. Drain the cooler pipe from its attachment to the frame retainers together with the vehicle. To install the cooler pipe place it into the vehicle space between frame retainers before attaching the frame retainer with its bolt/screw tightened to 10 nm (89 inch lbs.). The power steering gear needs a cooler pipe installation with 27 nm (20 ft. Lbs.) torque while using a hose clip during the process. After reattaching the power steering return hose to the cooler pipe you must raise the frame rear and install its bolts while tightening them to 165 nm (122 ft. Lbs.). The procedure starts by removing the utility stand followed by reattachment of the intermediate shaft to the steering gear along with installing the right side engine splash shield and lowering the vehicle before finally performing power steering system bleeding.

OEM 2006 Chevrolet Uplander Power Steering Hose

Power Steering Pressure Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Power Steering Hoses found

View related parts
2006 Chevrolet Uplander Power Steering Cooler Part Number: 15777213
$100.57 MSRP: $159.65
You Save: $59.08 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Power Steering Fluid Cooling; Power Steering Hose; Power Steering Return Hose; Cooling Pipe; Hose, Steering Fluid Cooler
- Replaced by: 19540437
- Item Weight: 1.70 Pounds
- Item Dimensions: 29.3 x 26.0 x 9.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777213
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Pipe Kit Part Number: 88963469
$15.20 MSRP: $30.53
You Save: $15.33 (51%)
ADD TO CART
Product Specifications
- Other Name: Pipe Kit, Steering Gear Left; Power Steering Hose; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.8 x 5.0 x 2.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88963469
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Return Hose Part Number: 15233978
Product Specifications
- Other Name: Hose; Power Steering Hose
- Replaced by: 15777212
- Item Weight: 1.60 Pounds
- Item Dimensions: 30.4 x 25.8 x 10.3 inches
- Condition: New
- SKU: 15233978
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Pressure Hose Part Number: 15777622
Product Specifications
- Other Name: Hose Assembly-Power Steering Gear Inlet; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure; Hose, Steering Gear Oil Pressure
- Replaces: 10311306
- Item Weight: 1.80 Pounds
- Item Dimensions: 22.9 x 20.5 x 2.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777622
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Pressure Hose Part Number: 15777209
Product Specifications
- Other Name: Hose Assembly-Power Steering Gear Inlet; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure; Hose, Steering Gear Oil Pressure
- Item Weight: 1.80 Pounds
- Item Dimensions: 23.2 x 17.9 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777209
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Cooler Part Number: 15777212
Product Specifications
- Other Name: Hose Assembly-Power Steering Fluid Cooling; Power Steering Hose; Power Steering Return Hose; Cooling Pipe; Hose, Steering Fluid Cooler
- Replaces: 15233978, 15197545
- Item Weight: 1.60 Pounds
- Item Dimensions: 30.7 x 25.8 x 10.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777212
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Pressure Hose Part Number: 19333426
Product Specifications
- Other Name: Hose, Steering Gear Oil Pressure; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure
- Replaces: 15777210
- Item Weight: 2.00 Pounds
- Item Dimensions: 29.5 x 16.9 x 9.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19333426
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Return Hose Part Number: 15777207
Product Specifications
- Other Name: Pipe, Steering Gear Oil Return; Power Steering Hose; Inlet Pipe
- Replaces: 15293050
- Item Weight: 0.70 Pounds
- Item Dimensions: 22.5 x 10.9 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777207
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS
View related parts
2006 Chevrolet Uplander Pipe Kit, Driver Side Part Number: 26081830
Product Specifications
- Other Name: Pipe Kit, Steering Gear; Power Steering Hose; Pressure Line; Line Kit; Line; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Position: Driver Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 10.7 x 3.7 x 1.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26081830
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Pipe Kit, Passenger Side Part Number: 26081831
Product Specifications
- Other Name: Pipe Kit, Steering Gear; Power Steering Hose; Pressure Line; Line Kit; Line; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Position: Passenger Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 18.2 x 3.1 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26081831
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Power Steering Return Hose Part Number: 15893685
Product Specifications
- Other Name: Pipe, Steering Gear Oil Return; Power Steering Hose; Inlet Pipe
- Item Weight: 2.00 Pounds
- Item Dimensions: 23.1 x 10.9 x 10.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15893685
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
2006 Chevrolet Uplander Pipe Kit Part Number: 88963470
Product Specifications
- Other Name: Pipe Kit, Hydraulic Steering Gear Pressure; Power Steering Hose; Pipe Kit, Steering Gear Oil Pressure
- Position: Passenger Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 18.5 x 4.8 x 2.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88963470
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Uplander Submodels:
- Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS

2006 Chevrolet Uplander Power Steering Hose

With a comprehensive array of OEM 2006 Chevrolet Uplander Power Steering Hose, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2006 Chevrolet Uplander Power Steering Hose are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2006 Chevrolet Uplander Power Steering Hose Parts and Q&A

Q: How to Replace a Power Steering Hose on 2006 Chevrolet Uplander?
A: The first step to change the power steering cooler pipe/hose requires lifting and supporting the vehicle followed by right side engine splash shield removal. A drain pan should be placed under the Power Steering Pump and gear while you disconnect the return hose from the cooler pipe. Steering control loss can result from damage so the intermediate shaft must be disconnected from the steering gear. A utility stand should support the frame's rear while you remove frame bolts to lower the back section below clearance level. The first step requires the power steering gear heat shield removal along with the hose clip before disconnecting the cooler pipe from the steering gear while extracting the retainer bolt/screw and retainer. Drain the cooler pipe from its attachment to the frame retainers together with the vehicle. To install the cooler pipe place it into the vehicle space between frame retainers before attaching the frame retainer with its bolt/screw tightened to 10 nm (89 inch lbs.). The power steering gear needs a cooler pipe installation with 27 nm (20 ft. Lbs.) torque while using a hose clip during the process. After reattaching the power steering return hose to the cooler pipe you must raise the frame rear and install its bolts while tightening them to 165 nm (122 ft. Lbs.). The procedure starts by removing the utility stand followed by reattachment of the intermediate shaft to the steering gear along with installing the right side engine splash shield and lowering the vehicle before finally performing power steering system bleeding.