How to replace the front shock absorber with RPO FE7 on Cadillac DeVille?

Start the process of swapping rpo fe7 strut assembly by detaching the three strut tower bolts first. Raising the vehicle then using frame support to allow the control arms to dangle freely. First disconnect the wheel speed sensor connector while removing the wheel speed sensor bracket from the dust shield. Start by detaching the brake line bracket from the strut and then remove the strut-to-knuckle bolts to extract the strut from the vehicle. Installation begins by putting the strut in position then following the service warnings shown on the fastener notices. Fasten the 3 strut tower bolts using washers while tightening them to 66 nm (49 ft. Lbs.). The installation process begins with tightening the strut to knuckle bolts and nuts to 177 nm (131 ft. Lbs.) and completing the procedure with a 23 nm (17 ft. Lbs.) torque on the brake line bracket to the strut. Attach the wheel speed sensor bracket to the dust shield and connect the wheel speed sensor connector. Secure the wheel and tire using a 125 nm torque (80 ft. Lbs.) while lowering the car to completion.

How to service and repair the front coil springs and shock absorber on Cadillac DeVille?

To service and repair the suspension strut, start by collecting the tools required: holding fixture base assembly (J3289-20), strut spring compressor (J34013-B), damper rod clamp (J34013-20), strut alignment rod (J34013-38), and strut compressor lower adapter (J34013-971). Replace the strut with the one from the vehicle, being cautious not to chip or scratch the coating of the suspension coil spring since damage to the paint will cause an early failure. Then, load the strut assembly into the strut spring compressor (J34013-B) and turn the spring compressor scrue until the spring slightly compresses. Hold onto the strut shaft and take off the strut shaft nut thereafter,, guide the strut shaft out of the strut assembly using the suitable tool while loosening the compressor screw. Keep swelling until you can delete the strut and spring. Installation: mount the damper rod clamp (J34013-20) on the strut shaft beside the strut compressor lower adapter (J34013-971), let the spring locate on top of the strut and lift the assembled to vertical inside the compressor. Make sure that the upper spring seat tab points to the inwards and the bearing is installed in the same direction as previously. Feed the clutch compressor screw alignment rod (J 34013-38) to guide the strut shaft, and then tighten the compressor screw clockwise to align the shaft in the assembly until the threads come out. Mount the washer, and undo the damper rod clamp (J34013-20), and tighten the strut mount nut to 75 nm (55 ft. Lbs.). Finally, take out the strut from the compressor and reassemble it on the vehicle.

OEM Cadillac DeVille Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

40 Shock Absorbers found

View related parts
Cadillac DeVille Shock Absorber Part Number: 88946013
$36.24 MSRP: $64.72
You Save: $28.48 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Front Shock; Shock; Absorber, Front And Rear Suspension
- Position: Front
- Replaces: 04993745, 22064046, 4993745, 22064047
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Cadillac DeVille | Base, Cabriolet, d'Elegance | 8 Cyl 4.1 L GAS
View related parts
Cadillac DeVille Shock Absorber Part Number: 88945188
$48.44 MSRP: $86.50
You Save: $38.06 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber, Rear Shock; Shock
- Position: Rear
- Replaces: 22064413, 22064299, 22064856, 22064265, 22046428, 22064422, 22064043, 22064101, 22046810
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Cadillac DeVille | Base, Cabriolet, d'Elegance | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Shock Absorber Part Number: 22064565
$215.77 MSRP: $405.21
You Save: $189.44 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock; Active to Passive Suspension Conversion Kit; Air Spring to Coil Spring Conversion Kit; Conversion Kit
- Position: Rear
- Replaced by: 22400392
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Cadillac DeVille | Base | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Shock Absorber, Front Part Number: 4993745
$36.24 MSRP: $64.72
You Save: $28.48 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly-Front Shock
- Position: Front
- Replaced by: 88946013
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Cadillac DeVille | Base, Cabriolet, d'Elegance | 8 Cyl 4.1 L GAS
View related parts
Cadillac DeVille Strut, Rear Part Number: 22047978
$256.61 MSRP: $502.41
You Save: $245.80 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut Assembly-Rear Suspension; Shock Absorber
- Position: Rear
- Replaced by: 22064179
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1989 Cadillac DeVille | Base, d'Elegance, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac DeVille Shock Absorber, Front Driver Side Part Number: 22064537
$173.26 MSRP: $323.30
You Save: $150.04 (47%)
ADD TO CART
Product Specifications
- Other Name: Strut Assembly, Front Suspension; Active to Passive Suspension Conversion; Air Spring to Coil Spring Kit.; Compressor Head; Striker; Strut
- Position: Front Driver Side
- Replaced by: 22400389
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2000 Cadillac DeVille | Base, Concours, d'Elegance, DHS, DTS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Macpherson Strut Part Number: 22189452
$173.26 MSRP: $323.30
You Save: $150.04 (47%)
ADD TO CART
Product Specifications
- Other Name: Active to Passive Suspension Conversion Kit; Air to Coil Spring Conversion; Shock Absorber.; Strut
- Position: Front
- Replaced by: 22400389
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Cadillac DeVille | Base, Concours | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Shock Absorber, Rear Part Number: 19299843
Product Specifications
- Other Name: Absorber Assembly, Rear Leveling Shock; Shock; Strut
- Position: Rear
- Replaces: 19180220, 22064671, 22064869, 19177314, 88955457, 88955461, 22064672, 22064809, 22064810, 22064808, 19207418, 22064664, 88955460, 19257784, 88955458, 22064665
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Strut, Driver Side Part Number: 22064723
Product Specifications
- Other Name: Strut, Front And Rear Suspension Conversion Kit from Active to Passive, Air Spring to Coil Spring, Shock Absorber
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Macpherson Strut Part Number: 22189454
Product Specifications
- Other Name: Shock Absorber; Strut; Strut, Front And Rear Suspension
- Position: Front
- Replaces: 22064321, 22064562
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Macpherson Strut Part Number: 88945833
$79.72 MSRP: $142.36
You Save: $62.64 (44%)
Product Specifications
- Other Name: Strut, Front Suspension; Shock Absorber; Strut
- Position: Front
- Replaces: 22113668, 22064566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Strut, Front Part Number: 22400389
Product Specifications
- Other Name: Strut Assembly, Front Suspension; Active to Passive Suspension Conversion; Air to Coil Spring Kit; Shock Absorber.
- Position: Front
- Replaces: 22064538, 22189453, 22064353, 22064537, 22189452, 22064351, 22064349, 22064512, 22064513, 22064355
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2000 Cadillac DeVille | Base, Concours, DHS, DTS, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Shock Absorber, Rear Part Number: 22064425
Product Specifications
- Other Name: Absorber Assembly-Rear Shock; Suspension Strut Assembly Kit; Air Suspension Strut; Complete Strut Kit; Complete Strut; Absorber, Front And Rear Suspension; Absorber, Shock Absorber Air Lift
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Cadillac DeVille | Base, Cabriolet, d'Elegance, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Shock Absorber, Rear Part Number: 22064426
Product Specifications
- Other Name: Absorber Assembly-Rear Shock; Suspension Strut Assembly Kit; Air Suspension Strut; Complete Strut Kit; Complete Strut; Absorber, Front And Rear Suspension; Absorber, Shock Absorber Air Lift
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Cadillac DeVille | Base, Cabriolet, d'Elegance, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Strut, Front Passenger Side Part Number: 22064724
Product Specifications
- Other Name: Strut Assembly, Front Suspension Right-Hand; Conversion Kit; Shock Absorber; Strut, Front And Rear Suspension
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Strut Part Number: 22189459
Product Specifications
- Other Name: Strut, Front And Rear Suspension; Shock Absorber
- Position: Rear
- Replaces: 22064501
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Shock Absorber Part Number: 22064596
Product Specifications
- Other Name: Absorber, Shock Absorber Air Lift; Active to Passive Suspension Conversion Kit; Air Spring to Coil Spring.; Shock
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Strut, Driver Side Part Number: 22064594
Product Specifications
- Other Name: Strut, Front And Rear Suspension Conversion Kit from Active to Passive, Air Spring to Coil Spring, Shock Absorber
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Cadillac DeVille | Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Shock Absorber Part Number: 22064727
Product Specifications
- Other Name: Absorber, Shock Absorber Air Lift; Active to Passive Suspension Conversion Kit; Air Spring to Coil Spring.; Shock; Strut
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Strut, Passenger Side Part Number: 22064595
Product Specifications
- Other Name: Strut, Front And Rear Suspension Conversion Kit from Active to Passive, Air Spring to Coil Spring, Shock Absorber
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Cadillac DeVille | Concours, d'Elegance | 8 Cyl 4.6 L GAS

| Page 1 of 2 |Next >

1-20 of 40 Results

Cadillac DeVille Shock Absorber

Want to cut long-term maintenance and repair costs? Choose OEM Shock Absorber. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac DeVille parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac DeVille Shock Absorber includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The part in question, namely the Shock Absorber is among the essential parts of the Cadillac DeVille automobiles, responsible for the stability and management of the vehicle along with the struts. These members contribute to reduce bouncing and damp shocks' impulses for enhanced ride comfort and contact with the road. Based on the Cadillac DeVille automobiles, the different types of the shock absorbers used include the twin-tube and mono-tube shocks that work in different mechanisms such as the regulation of the hydraulic shock fluid flow to optimize the car's performance depending on the driving conditions. Specialist applications like the Position Sensitive Damping (PSD) and Acceleration Sensitive Damping (ASD) make shock absorber's reactions to any given driving conditions more advanced and there are technologies like electrorheological and magnetorheological dampers permitting semi-active and adaptive suspension systems, that turn comfort and control into an optimum one depending on the current driving condition.

Cadillac DeVille Shock Absorber Parts and Q&A

Strut, Front Driver Side
22064782
Q: How to replace the front shock absorber with RPO FE7 on Cadillac DeVille?
A:
Start the process of swapping rpo fe7 strut assembly by detaching the three strut tower bolts first. Raising the vehicle then using frame support to allow the Control Arms to dangle freely. First disconnect the wheel speed sensor connector while removing the wheel speed sensor bracket from the dust shield. Start by detaching the brake line bracket from the strut and then remove the strut-to-knuckle bolts to extract the strut from the vehicle. Installation begins by putting the strut in position then following the service warnings shown on the fastener notices. Fasten the 3 strut tower bolts using washers while tightening them to 66 nm (49 ft. Lbs.). The installation process begins with tightening the strut to knuckle bolts and nuts to 177 nm (131 ft. Lbs.) and completing the procedure with a 23 nm (17 ft. Lbs.) torque on the brake line bracket to the strut. Attach the wheel speed sensor bracket to the dust shield and connect the wheel speed sensor connector. Secure the wheel and tire using a 125 nm torque (80 ft. Lbs.) while lowering the car to completion.
Strut, Front Passenger Side
22064783
Q: How to service and repair the front coil springs and shock absorber on Cadillac DeVille?
A:
To service and repair the suspension strut, start by collecting the tools required: holding fixture base assembly (J3289-20), strut spring compressor (J34013-B), damper rod clamp (J34013-20), strut alignment rod (J34013-38), and strut compressor lower adapter (J34013-971). Replace the strut with the one from the vehicle, being cautious not to chip or scratch the coating of the suspension coil spring since damage to the paint will cause an early failure. Then, load the strut assembly into the strut spring compressor (J34013-B) and turn the spring compressor scrue until the spring slightly compresses. Hold onto the strut shaft and take off the strut shaft nut thereafter,, guide the strut shaft out of the strut assembly using the suitable tool while loosening the compressor screw. Keep swelling until you can delete the strut and spring. Installation: mount the damper rod clamp (J34013-20) on the strut shaft beside the strut compressor lower adapter (J34013-971), let the spring locate on top of the strut and lift the assembled to vertical inside the compressor. Make sure that the upper spring seat tab points to the inwards and the bearing is installed in the same direction as previously. Feed the clutch compressor screw alignment rod (J 34013-38) to guide the strut shaft, and then tighten the compressor screw clockwise to align the shaft in the assembly until the threads come out. Mount the washer, and undo the damper rod clamp (J34013-20), and tighten the strut mount nut to 75 nm (55 ft. Lbs.). Finally, take out the strut from the compressor and reassemble it on the vehicle.