How to replace the front brake calipers on Chevrolet HHR?

Unless the brake master cylinder reservoir contains less than half its fluid capacity you should remove excess fluid before starting brake caliper replacement. Lift up the vehicle and take off the tire and wheel unit. Replace the rotor to hub by hand-tightening two wheel nuts between opposite wheel studs. Secure a c-clamp on top of the brake caliper housing then tighten it until the piston can move through the brake rotor. Take the clamp off afterward. Take off the brake hose fitting bolt then remove both brake hose fitting gaskets and brake hose before plugging the brake system to avoid fluid leaks. Discard the removed parts. Take out the brake caliper guide pin bolts then pull off the caliper from its bracket. Check if guide pins move properly and replace them plus the boots when needed. Place the caliper on the bracket and fasten its guide pins with torque at 35 nm (26 lb ft). Connect the brake hose fitting hardware along with gaskets onto the brake hose. Afterward attach the hose assembly to the caliper and torque the bolt to 40 nm (30 lb ft). Let the hydraulic brake system air out then disconnect the wheel nuts as you reinstall the tire wheels. Lower the car and press the Brake Pedal slowly from zero to two thirds distance with the engine off. Repeat this three times to help brake caliper pistons settle.

OEM Chevrolet HHR Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Calipers found

View related parts
Chevrolet HHR Caliper, Green Line Part Number: 19368940
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Replaces: 22705314
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2011 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
Chevrolet HHR Caliper, Green Line Part Number: 19368939
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Replaces: 22705313
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2011 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
Chevrolet HHR Caliper, Front Passenger Side Part Number: 25894356
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chevrolet HHR | SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
Chevrolet HHR Caliper, Front Driver Side Part Number: 25894355
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chevrolet HHR | SS, SS Panel | 4 Cyl 2.0 L GAS

Chevrolet HHR Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet HHR parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet HHR Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Brake Caliperss in Chevrolet HHR is involved in the brake system of the vehicle where it is responsible for use of hydraulic pressure obtained from the master cylinder to produce mechanical force. This force is necessary to apply brake pads against the rotor or drum which in effect slow or stall the car. Chevrolet HHR models utilize two primary types of brake calipers. The fixed calipers have the mounting of pistons on either side of the rotor while the floating ones have a mounting of only one piston that slides over the rotor to exert pressure; this kind of calipers wear the rotors unevenly if not well maintained. HHR brake calipers are normally constructed out of either cast iron bodies with steel or phenolic pistons. Options are available for performance, which are intended upgrades to original equipment calipers, including better braking and looks. It is extremely important because of such problems as leakage or stuck pistons can cause severe problems with the brakes themselves. In general, the brake caliper plays a critical role of maintaining safe and efficient braking system of Chevrolet HHR vehicles.

Chevrolet HHR Brake Calipers Parts Questions & Experts Answers

Caliper, Green Line
19368939
Q: How to replace the front brake calipers on Chevrolet HHR?
A:
Unless the brake master cylinder reservoir contains less than half its fluid capacity you should remove excess fluid before starting brake caliper replacement. Lift up the vehicle and take off the tire and wheel unit. Replace the rotor to hub by hand-tightening two wheel nuts between opposite wheel studs. Secure a c-clamp on top of the brake caliper housing then tighten it until the piston can move through the brake rotor. Take the clamp off afterward. Take off the brake hose fitting bolt then remove both brake hose fitting gaskets and brake hose before plugging the brake system to avoid fluid leaks. Discard the removed parts. Take out the brake caliper guide pin bolts then pull off the caliper from its bracket. Check if guide pins move properly and replace them plus the boots when needed. Place the caliper on the bracket and fasten its guide pins with torque at 35 nm (26 lb ft). Connect the brake hose fitting hardware along with gaskets onto the brake hose. Afterward attach the hose assembly to the caliper and torque the bolt to 40 nm (30 lb ft). Let the hydraulic brake system air out then disconnect the wheel nuts as you reinstall the tire wheels. Lower the car and press the Brake Pedal slowly from zero to two thirds distance with the engine off. Repeat this three times to help brake caliper pistons settle.