How to service and repair the ABS Control Module on Chevrolet Venture?

Service and repair operations for the ABS Control Module require dismissing the ignition switch to the off position in order to safeguard equipment components. Start by removing the engine compartment housing of the air cleaner and follow with the removal of the red locking tab situated on the connector lock tab. The sliding connector cover needs to be positioned to the open position while pushing down on the lock tab to disconnect the ABS Control Module harness connector. Clear the assembly components before disconnecting the master cylinder mount nuts while placing the master cylinder in position without detaching the brake pipes. Separate the ABS Control Module from the bpmv by removing four screws while ensuring the use of tools keeps everything in place and the bpmv surface intact and solenoid valves free of damage. Use gentle force to remove the ABS Control Module away from the bpmv until the two components separate. You must clean the bpmv surface after spraying it with alcohol using a clean rag before installing the ABS Control Module onto the bpmv and fastening it with the four screws which require tightening at 5 nm (44 inch lbs.). Attach the master cylinder to the Brake Booster by using and tightening mount nuts at 25 nm (18 ft. Lbs.). Refit the ABS Control Module harness connector by locking the tab then return the sliding connector protector into its blocking position before inserting the red locking mechanism. Complete the installation of the air cleaner housing then activate the ignition switch to run mode while maintaining engine and run the a diagnostic system check - abs.

How to replace the ABS Control Module on Chevrolet Venture?

The replacement process of the ABS Control Module requires the ignition switch to be set to off. First remove the air cleaner housing from the engine compartment followed by ABS Control Module harness connector disconnection. Remove all dirt from the assembly and disconnect the pump motor connector found at the ABS Control Module's bottom side. Remove the six screws between ABS Control Module and bpmv with care to prevent damaging either the seal or solenoid valves by extracting the ABS Control Module away from the brake pressure modulator valve. The installation requires new wave springs along with screws which come with new ABS Control Module and requires a clean bpmv surface through alcohol application with a new cleaned rag. Install the ABS Control Module onto the bpmv component before tightening 6 screws starting with the top 4 screws at 5 nm (44 inch lbs.) according to an x pattern configuration and completing with the bottom 2 screws at the same torque setting. Recouple the pump motor connector to the lower part of the ABS Control Module while attaching the ABS Control Module harness connector with its secure locking mechanism. After installing the air cleaner housing you should enable the ignition switch to run mode without starting the engine then execute diagnostic system checks.

OEM Chevrolet Venture ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 ABS Control Modules found

View related parts
Chevrolet Venture Control Module Part Number: 9385320
$584.41 MSRP: $948.45
You Save: $364.04 (39%)
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Electronic Traction Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 18078137
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 12201164, 12225451
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Motor Assembly Part Number: 18024455
Product Specifications
- Other Name: Motor Kit, Electronic Traction Control Brake Pressure Mode Valve; ABS Pump And Motor Assembly; Motor & Pump; Motor Pack; Motor; Motor Kit, Electronic Brake Control
- Replaces: 18021107
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Module Part Number: 12020004
Product Specifications
- Other Name: ABS Control Module; Module, Instrument Cluster Warning; Electronic Brake Control; Voltage And Glow Plug; Catalytic Converter; Chassis Wiring
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 18078138
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module
- Replaces: 12223396
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Motor Assembly Part Number: 18024454
Product Specifications
- Other Name: Motor Kit, Electronic Brake Control; ABS Pump And Motor Assembly; Motor & Pump; Motor Pack; Motor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 9385340
Product Specifications
- Other Name: Module Assembly, Electronic Traction Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 18078148
Product Specifications
- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 12227273
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 18078146
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Motor Assembly Part Number: 18024482
Product Specifications
- Other Name: Motor Kit, Electronic Brake Control; ABS Pump And Motor Assembly; Motor & Pump
- Replaces: 91172937
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 16188001
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Venture | Base, LS | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 12227273
Product Specifications
- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module; Module, Electronic Brake Control
- Replaced by: 18078148
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Chevrolet Venture | LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 12203088
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 9388001, 09388001
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Venture Control Module Part Number: 12203084
Product Specifications
- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 12201159, 09387998, 9387998
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS

Chevrolet Venture ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Venture parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Venture ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

There is the Chevrolet Venture ABS Control Module that is used in the anti-lock braking system and is highly reliable and performs well in the models of Chevrolet Venture made from 1997 to 2005. For vehicle safety this advanced ABS Control Module is responsible for preventing wheel lock-up at times of heavy braking and hence maintaining vehicle stability and reducing chances of the vehicle skidding. Some of the component that this module works well with include; wheel speed sensors, valves, a pump, and an ECU in their the task of regulating brake pressure. However, it is important to note that the Chevrolet Venture ABS control module has changed with time and now has sub systems such as the electronic stability control that help to control rotation through selectively braking individual tires. This capability is more useful for drivers especially when they are struggling with different road surfaces. A minivan created and marketed by Chevrolet since 1997 is named as Chevrolet Venture which comes in the basic, LS as well as LT designs, the product being essential to the Stability Control and Anti-locking Braking systems. Mentioned among the most demanded minivans for the American families, the Chevrolet Venture has a 180-hp LA1 V6 power plant and the four-speed automatic transmission. The ABS Control Module is also useful in enhancing the brake's effectiveness and take its share to the safety feature of Chevrolet Venture and help in creating a demand on the market. Compatibility with different Venture models and such features as advanced functionality of the Chevrolet Venture ABS Control Module contribute to stress-free traveling for drivers and passengers.

Chevrolet Venture ABS Control Module Parts and Q&A

Control Module
12203084
Q: How to service and repair the ABS Control Module on Chevrolet Venture?
A:
Service and repair operations for the ABS Control Module require dismissing the ignition switch to the off position in order to safeguard equipment components. Start by removing the engine compartment housing of the air cleaner and follow with the removal of the red locking tab situated on the connector lock tab. The sliding connector cover needs to be positioned to the open position while pushing down on the lock tab to disconnect the ABS Control Module harness connector. Clear the assembly components before disconnecting the master cylinder mount nuts while placing the master cylinder in position without detaching the brake pipes. Separate the ABS Control Module from the bpmv by removing four screws while ensuring the use of tools keeps everything in place and the bpmv surface intact and solenoid valves free of damage. Use gentle force to remove the ABS Control Module away from the bpmv until the two components separate. You must clean the bpmv surface after spraying it with alcohol using a clean rag before installing the ABS Control Module onto the bpmv and fastening it with the four screws which require tightening at 5 nm (44 inch lbs.). Attach the master cylinder to the Brake Booster by using and tightening mount nuts at 25 nm (18 ft. Lbs.). Refit the ABS Control Module harness connector by locking the tab then return the sliding connector protector into its blocking position before inserting the red locking mechanism. Complete the installation of the air cleaner housing then activate the ignition switch to run mode while maintaining engine and run the a diagnostic system check - abs.
Control Module
18078148
Q: How to replace the ABS Control Module on Chevrolet Venture?
A:
The replacement process of the ABS Control Module requires the ignition switch to be set to off. First remove the air cleaner housing from the engine compartment followed by ABS Control Module harness connector disconnection. Remove all dirt from the assembly and disconnect the pump motor connector found at the ABS Control Module's bottom side. Remove the six screws between ABS Control Module and bpmv with care to prevent damaging either the seal or solenoid valves by extracting the ABS Control Module away from the brake pressure modulator valve. The installation requires new wave springs along with screws which come with new ABS Control Module and requires a clean bpmv surface through alcohol application with a new cleaned rag. Install the ABS Control Module onto the bpmv component before tightening 6 screws starting with the top 4 screws at 5 nm (44 inch lbs.) according to an x pattern configuration and completing with the bottom 2 screws at the same torque setting. Recouple the pump motor connector to the lower part of the ABS Control Module while attaching the ABS Control Module harness connector with its secure locking mechanism. After installing the air cleaner housing you should enable the ignition switch to run mode without starting the engine then execute diagnostic system checks.