How to replace the Power Steering Hose for the gear inlet and outlet on GMC Canyon?

Start the replacement of the power steering gear inlet and outlet hose by positioning a drain pan beneath the vehicle. First disconnect the Power Steering Hose assembly from the Power Steering Pump then securely place safety stands under the vehicle before raising it upwards. First remove the Power Steering Hose assembly bracket retaining bolts then proceed to disconnect the retaining bolt between the Power Steering Hose assembly and power steering gear. The power steering gear hose should be disconnected from the steering gear followed by vehicle removal while cleaning both ports throughly to protect power steering system components from damage and contamination. The power steering gear oil seal remover/installer (J 44586) allows replacement of power steering gear oil seals when necessary and should be used to remove old oil seals from the power steering gear. Using j 44586 tool again install new oil seals into their appropriate positions by cleaning both inlet and outlet ports beforehand. After guiding the power steering gear into position you should connect its hose assembly to the bolt at the power steering gear then tighten the retaining bolt at 12 n.m (106 lb in). Install the Power Steering Hose assembly clip retaining bolts before tightening them to 9 n.m (79 lb in). To complete installation lower the vehicle stemming the Power Steering Pump connection through a 25 n.m (18 lb ft) torque force. To finish, drain the pan and add correct fluid to the reservoir before completing system bleeding.

OEM GMC Canyon Power Steering Hose

Power Steering Pressure Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Power Steering Hoses found

View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 20934197
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 20934195
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Pipe, Passenger Side Part Number: 19133632
Product Specifications
- Other Name: Pipe, Hydraulic Steering Gear Pressure; Power Steering Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Pipe, Driver Side Part Number: 19133627
Product Specifications
- Other Name: Pipe, Hydraulic Steering Gear Pressure; Power Steering Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 15136892
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 GMC Canyon | SL, SLE, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 15136891
$124.62 MSRP: $196.08
You Save: $71.46 (37%)
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 GMC Canyon | SL, SLE, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Pipe, Driver Side Part Number: 26095516
Product Specifications
- Other Name: Power Steering Hose; Pipe, Hydraulic Steering Gear Pressure
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 GMC Canyon | SL, SLE, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Pipe, Passenger Side Part Number: 26095515
Product Specifications
- Other Name: Pipe Assembly, Steering Gear Right; Power Steering Hose; Pipe, Hydraulic Steering Gear Pressure
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 GMC Canyon | SL, SLE, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Pipe, Driver Side Part Number: 26095514
Product Specifications
- Other Name: Power Steering Hose; Pipe, Hydraulic Steering Gear Pressure
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 GMC Canyon | SL, SLE, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Pipe, Passenger Side Part Number: 26095513
Product Specifications
- Other Name: Pipe, Steering Gear; Power Steering Hose; Pipe, Hydraulic Steering Gear Pressure
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 GMC Canyon | SL, SLE, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 20934198
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 20934196
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Replaces: 15849435, 25833643
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 20933948
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Replaces: 25970566, 25776470
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 GMC Canyon | SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 20933939
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009 GMC Canyon | SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Pipe, Driver Side Part Number: 19133631
Product Specifications
- Other Name: Pipe, Hydraulic Steering Gear Pressure; Power Steering Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Pipe, Passenger Side Part Number: 19133628
Product Specifications
- Other Name: Pipe, Hydraulic Steering Gear Pressure; Power Steering Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Power Steering Pressure Hose Part Number: 15146387
Product Specifications
- Other Name: Hose, Hydraulic Steering Gear Pressure; Power Steering Hose; Hose & Tube Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 GMC Canyon | SL, SLE, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS

GMC Canyon Power Steering Hose

Want to cut long-term maintenance and repair costs? Choose OEM Power Steering Hose. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Canyon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Canyon Power Steering Hose includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Power Steering Hose is a complex part that plays a critical role to the improvement of the quality of GMC Canyon vehicles. This hose completes the power steering pump to the steering gear and relays the flow of the pressurized steering fluid for proper steering operation. This Power Steering Hose is built with strength in order to endure the different key performance areas that should be delivered every time a Canyon is driven. Compatibility with multiple Canyon models starting from the model that began its production in 2004 keeps the drivers in proper control of the car's steering performance in different models and configurations whether as 2WD or 4WD. Therefore, the role of Power Steering Hose is not only to pass on power but also to avoid leaks that may cause steering problems hence improving efficiency and safety of the car. Some of the Power Steering Hose features more unique, these include high-pressure fittings and the possible of bending metal tubing, that makes it to stick well and without leaking. As for the maintenance, it is crucial to mind about this hose's condition as well as the proper installation of such a part to retain the integrity of the power steering system and, thus, provide a safer and more enjoyable driving across the GMC Canyon. Today the Power Steering Hose is simply one of those parts that until proven otherwise you would not want to be caught with a car without such part.

GMC Canyon Power Steering Hose Parts and Q&A

Power Steering Pressure Hose
20934195
Q: How to replace the Power Steering Hose for the gear inlet and outlet on GMC Canyon?
A:
Start the replacement of the power steering gear inlet and outlet hose by positioning a drain pan beneath the vehicle. First disconnect the Power Steering Hose assembly from the Power Steering Pump then securely place safety stands under the vehicle before raising it upwards. First remove the Power Steering Hose assembly bracket retaining bolts then proceed to disconnect the retaining bolt between the Power Steering Hose assembly and power steering gear. The power steering gear hose should be disconnected from the steering gear followed by vehicle removal while cleaning both ports throughly to protect power steering system components from damage and contamination. The power steering gear oil seal remover/installer (J 44586) allows replacement of power steering gear oil seals when necessary and should be used to remove old oil seals from the power steering gear. Using j 44586 tool again install new oil seals into their appropriate positions by cleaning both inlet and outlet ports beforehand. After guiding the power steering gear into position you should connect its hose assembly to the bolt at the power steering gear then tighten the retaining bolt at 12 n.m (106 lb in). Install the Power Steering Hose assembly clip retaining bolts before tightening them to 9 n.m (79 lb in). To complete installation lower the vehicle stemming the Power Steering Pump connection through a 25 n.m (18 lb ft) torque force. To finish, drain the pan and add correct fluid to the reservoir before completing system bleeding.