Other Name: Regulator, Rear Door Window Regulator; Power Window Motor and Regulator Assembly; Window Motor; Regulator; Regulator, Door And End Gate Window
Position: Rear Driver Side
Replaces: 15113353, 15919133
Fits the following GMC Models:
Canyon | 2004-2012 | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
Other Name: Regulator, Front Door Window Regulator; Regulator
Position: Front Passenger Side
Fits the following GMC Models:
C1500 | 1988-1999 | Sierra, Sierra GT, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX, Sierra Special | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL
C1500 Suburban | 1992-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
C2500 | 1988-2000 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
C2500 Suburban | 1992-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
C3500 | 1988-2000 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
K1500 | 1988-1999 | Sierra, Sierra SL, Sierra SLE, Sierra SLS, Sierra SLT, Sierra SLX, Sierra Special, Sierra Sport | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL
K1500 Suburban | 1992-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
K2500 | 1988-2000 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
K2500 Suburban | 1992-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
K3500 | 1988-2000 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
Other Name: Regulator, Rear Door Window Regulator; Regulator, Door And End Gate Window; Window Regulator
Position: Rear Passenger Side
Replaces: 15930530
Fits the following GMC Models:
Sierra 1500 | 2007-2013 | Denali, Hybrid, SL, SLE, SLT, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Sierra 2500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Sierra 3500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Other Name: Regulator, Rear Door Window Regulator; Regulator, Door And End Gate Window; Window Regulator
Position: Rear Driver Side
Replaces: 15930529
Fits the following GMC Models:
Sierra 1500 | 2007-2013 | Denali, Hybrid, SL, SLE, SLT, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Sierra 2500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Sierra 3500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Q: How to replace the rear side door window regulator on GMC Envoy?
A: You need to start your replacement of the rear side door Window Regulator by taking out the door trim panel along with both water deflector and speaker. Open the regulator window carrier bolts before lifting and sustaining the window in position. The first step is to disconnect the electrical connector at the regulator motor before loosening 3 bolts (part number 123456) which holds the Window Regulator assembly inside the door. Finalize the process by removing the assembly itself. Install the new Window Regulator assembly into its door position while tightening the 3 bolts (part number 123456) to 10 n.m (89 lb in). The regulator motor gets its electrical connector now followed by removing the window support so window lowering onto the regulator window carrier becomes possible. Loosen the regulator window carrier bolts first and then run the window to its highest point inside the channels before torquing the bolts to 10 n.m (89 lb in). Complete the process by returning the speaker and water deflector along with door trim panel.
Q: How to Service and Repair a Front Door Window Regulator on GMC Canyon?
A: Begin the front door Window Regulator replacement operation by removing both trim panel and water deflector elements of the front door. First disconnect the bolts holding the front door window to the Window Regulator and take away the window. Disconnect the electrical connector from the Window Regulator motor when a31 is installed. First loosen the bolts at keyhole slot locations which connect the Window Regulator to inner panel before taking out the rest of the fasteners between the panel and regulator. First lift the Window Regulator through the slots of the keyhole before removing it through the access opening. New window regulators should be inserted into the front door through the access hole and aligned by inserting the regulator bolts into the keyhole slots in the inner panel. Fasten the regulator retaining piece to the door while securing its fasteners to 9 n.m (80 lb in) torque. Reconnect the electrical connector to the Window Regulator motor when vehicle is equipped with a31. Replace the front door window before fastening it securely using the bolts which should be tightened at 9 n.m (80 lb in). At the end of this procedure install both the front door water deflector and front door trim panel.
Q: How to replace the front side door window regulator on GMC Acadia?
A: The door trim panel along with the water deflector must be removed before starting to replace the front side door Window Regulator. Begin by disassembly of the energy absorber retainers and absorber before removing the two bolting plates which hide the regulator holes. You should loosen the three bolts which connect window guide to regulator and then elevate the window to reach its maximum upward position. Detach the electrical connector from the regulator motor followed by loosening the upper bolt holding it to the upper inner door area. First remove the motor securing nut from the door then go ahead and take out the lower bolt . Raise the regulator/motor upward until the upper bolts uncover from the door then normalize the upper assembly forward. The lower portion of the regulator passes through the door opening first for removal and the upper bolt on the regulator can be removed next. The new regulator will receive the power Window Motor from the old one. To install the regulator place the upper bolt half-installed on the regulator as you gently feed it through the door opening oriented at a semi-horizontal angle before positioning it fully forward into the door cavity and rotating it to reach its vertical position. Proceed to mount the regulator on the door sheet metal by using the existing upper bolt. Then untether the window support before financially positioning the window on the regulator guide. Tighten the regulator carrier bolts only slightly before elevating the window to its maximum position while keeping it inside the channels properly. Fasten the retaining nut holding the motor to the door while tightening it to 9 n.m (80 lb in). Use bolts (1, 4) to attach the regulator to the door before tightening them to 10 n.m (88 loc in). Attach the electrical connector to the regulator motor followed by energy absorber retainer and absorber installation on the door and completing with regulator bolt hole covers together with water deflector and door trim panel.