Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 88982497
Inner Boot

2003-2014 GM

Customer Questions & Expert Answers (6)
GM 88982497 Inner Boot
  • Part Description
    Boot Kit, Front Axle; CV Boot
  • Position
    Front
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • 2012 GMC Savana 1500 Inner Boot Diagram for 88982497
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 88982497

  • Vehicle Fitment

    Year Make Model Trim Engine
    2003-2014 Chevrolet Express 1500Base, LS, LT6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2003-2014 Chevrolet Express 2500Base, LS, LT6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
    2003-2014 Chevrolet Express 3500Base, LS, LT8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
    2003-2014 GMC Savana 1500Base, LS, LT, SLE6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2003-2014 GMC Savana 2500Base, LS, LT, SLE6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
    2003-2014 GMC Savana 3500Base, LS, LT, SLE8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is 88982497 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88982497 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair the CV Boot and CV Joint on Chevrolet Express 2500? Posted by Customer
    A:
    Begin constant velocity joint boot maintenance and repair by removing the wheel drive shaft through correct procedures. Set the wheel drive shaft on top of a bench vise then cover its Axle Shaft with a shop towel. Use side cutters to remove the large seal clamp and small seal clamp then throw away these clamps. Move the seal behind the joint face by separating it from the joint outer race at the large end. Use an assistant to maintain the joint housing while an operator removes the outer joint from the wheel drive shaft bar after cleaning grease from the joint inner race cage and balls. First place a wood block between the seal and joint face at the joint area before hitting the block with a hammer to compress the Axle Shaft retaining ring until the outer joint detaches. The maintenance process requires wheel drive shaft bar operators to first remove both the retaining ring and seal. Begin installation by placing the large clamp and the small clamp on the seal before placing the seal onto the wheel drive shaft bar and adding the retaining ring. After using service kit grease to fill the outer joint you should position it at a horizontal angle while connecting inner race splines to Axle Shaft splines. Compress the Axle Shaft retaining ring using a flat-bladed screwdriver or equivalent tool to push the ring groove into the wheel drive shaft's open end while you fully press the outer joint onto the Axle Shaft. Work your way around the retaining ring until it becomes fully compressed. Use a wood block to protect the outer joint threaded shaft end while you hammer it until complete onto the wheel drive shaft bar. The mating groove in the wheel drive shaft bar must receive the small end of the seal before aligning the stepped surfaces of the Axle Shaft with its inner race. Begin by applying clamp pliers (J 43218) to compress the small clamp. Maintain compression until dimension (A) reaches 0.5-1.6 mm (0.02-0.06 in). After venting the joint, finish by securing the large clamp using clamp pliers (J 43218) until dimension (A) stands at 0.5-1.6 mm (0.02-0.06 in). Programming of the wheel drive shaft must be the final stage of the installation process.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair the CV Boot and CV Joint on Chevrolet Express 3500? Posted by Customer
    A:
    Begin constant velocity joint boot maintenance and repair by removing the wheel drive shaft through correct procedures. Set the wheel drive shaft on top of a bench vise then cover its Axle Shaft with a shop towel. Use side cutters to remove the large seal clamp and small seal clamp then throw away these clamps. Move the seal behind the joint face by separating it from the joint outer race at the large end. Use an assistant to maintain the joint housing while an operator removes the outer joint from the wheel drive shaft bar after cleaning grease from the joint inner race cage and balls. First place a wood block between the seal and joint face at the joint area before hitting the block with a hammer to compress the Axle Shaft retaining ring until the outer joint detaches. The maintenance process requires wheel drive shaft bar operators to first remove both the retaining ring and seal. Begin installation by placing the large clamp and the small clamp on the seal before placing the seal onto the wheel drive shaft bar and adding the retaining ring. After using service kit grease to fill the outer joint you should position it at a horizontal angle while connecting inner race splines to Axle Shaft splines. Compress the Axle Shaft retaining ring using a flat-bladed screwdriver or equivalent tool to push the ring groove into the wheel drive shaft's open end while you fully press the outer joint onto the Axle Shaft. Work your way around the retaining ring until it becomes fully compressed. Use a wood block to protect the outer joint threaded shaft end while you hammer it until complete onto the wheel drive shaft bar. The mating groove in the wheel drive shaft bar must receive the small end of the seal before aligning the stepped surfaces of the Axle Shaft with its inner race. Begin by applying clamp pliers (J 43218) to compress the small clamp. Maintain compression until dimension (A) reaches 0.5-1.6 mm (0.02-0.06 in). After venting the joint, finish by securing the large clamp using clamp pliers (J 43218) until dimension (A) stands at 0.5-1.6 mm (0.02-0.06 in). Programming of the wheel drive shaft must be the final stage of the installation process.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair the CV Boot and CV Joint on GMC Savana 2500? Posted by Customer
    A:
    Begin constant velocity joint boot maintenance and repair by removing the wheel drive shaft through correct procedures. Set the wheel drive shaft on top of a bench vise then cover its Axle Shaft with a shop towel. Use side cutters to remove the large seal clamp and small seal clamp then throw away these clamps. Move the seal behind the joint face by separating it from the joint outer race at the large end. Use an assistant to maintain the joint housing while an operator removes the outer joint from the wheel drive shaft bar after cleaning grease from the joint inner race cage and balls. First place a wood block between the seal and joint face at the joint area before hitting the block with a hammer to compress the Axle Shaft retaining ring until the outer joint detaches. The maintenance process requires wheel drive shaft bar operators to first remove both the retaining ring and seal. Begin installation by placing the large clamp and the small clamp on the seal before placing the seal onto the wheel drive shaft bar and adding the retaining ring. After using service kit grease to fill the outer joint you should position it at a horizontal angle while connecting inner race splines to Axle Shaft splines. Compress the Axle Shaft retaining ring using a flat-bladed screwdriver or equivalent tool to push the ring groove into the wheel drive shaft's open end while you fully press the outer joint onto the Axle Shaft. Work your way around the retaining ring until it becomes fully compressed. Use a wood block to protect the outer joint threaded shaft end while you hammer it until complete onto the wheel drive shaft bar. The mating groove in the wheel drive shaft bar must receive the small end of the seal before aligning the stepped surfaces of the Axle Shaft with its inner race. Begin by applying clamp pliers (J 43218) to compress the small clamp. Maintain compression until dimension (A) reaches 0.5-1.6 mm (0.02-0.06 in). After venting the joint, finish by securing the large clamp using clamp pliers (J 43218) until dimension (A) stands at 0.5-1.6 mm (0.02-0.06 in). Programming of the wheel drive shaft must be the final stage of the installation process.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair the CV Boot and CV Joint on GMC Savana 1500? Posted by Customer
    A:
    Begin constant velocity joint boot maintenance and repair by removing the wheel drive shaft through correct procedures. Set the wheel drive shaft on top of a bench vise then cover its Axle Shaft with a shop towel. Use side cutters to remove the large seal clamp and small seal clamp then throw away these clamps. Move the seal behind the joint face by separating it from the joint outer race at the large end. Use an assistant to maintain the joint housing while an operator removes the outer joint from the wheel drive shaft bar after cleaning grease from the joint inner race cage and balls. First place a wood block between the seal and joint face at the joint area before hitting the block with a hammer to compress the Axle Shaft retaining ring until the outer joint detaches. The maintenance process requires wheel drive shaft bar operators to first remove both the retaining ring and seal. Begin installation by placing the large clamp and the small clamp on the seal before placing the seal onto the wheel drive shaft bar and adding the retaining ring. After using service kit grease to fill the outer joint you should position it at a horizontal angle while connecting inner race splines to Axle Shaft splines. Compress the Axle Shaft retaining ring using a flat-bladed screwdriver or equivalent tool to push the ring groove into the wheel drive shaft's open end while you fully press the outer joint onto the Axle Shaft. Work your way around the retaining ring until it becomes fully compressed. Use a wood block to protect the outer joint threaded shaft end while you hammer it until complete onto the wheel drive shaft bar. The mating groove in the wheel drive shaft bar must receive the small end of the seal before aligning the stepped surfaces of the Axle Shaft with its inner race. Begin by applying clamp pliers (J 43218) to compress the small clamp. Maintain compression until dimension (A) reaches 0.5-1.6 mm (0.02-0.06 in). After venting the joint, finish by securing the large clamp using clamp pliers (J 43218) until dimension (A) stands at 0.5-1.6 mm (0.02-0.06 in). Programming of the wheel drive shaft must be the final stage of the installation process.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step after completing the installation for the 2009 GMC Savana 3500? Posted by Customer
    A:
    Reinstall the wheel drive shaft.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Inner Boot 88982497 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88982497 Inner Boot is available in the market under the name GM CV Boot. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88982497 Inner Boot fits certain Chevrolet Express 1500, Express 2500, Express 3500 models, as well as GMC Savana 2500, Savana 3500, Savana 1500 models.
The original GM component designated by manufacturer part number 88982497 maintains top performance when functioning as the Boot Kit, Front Axle; CV Boot unit at its Front. The component 88982497 is constructed from durable material and its dimensions span 7.8 x 5.1 x 5.9 inches while weighing 1.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 88982497 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.